User manual JVC MX-G51R

[. . . ] COMPACT COMPONENT SYSTEM CA-MXG51R DISC CHANGE STANDBY STANDBY/ON ECO PLAY & EXCHANGE CD-R/RW PLAYBACK COMPACT COMPONENT SYSTEM MX-G51R COMPACT DIGITAL AUDIO SOUND MODE SUBWOOFER LEVEL PRESET STANDBY/ON SET SLEEP 1 4 7 10 2 5 8 +10 3 6 9 SUBWOOFER LEVEL CANCEL /DEMO AUX SOUND MODE PHONES TUNING CLOCK / TIMER DISPLAY REPEAT PROGRAM RANDOM FM MODE FADE MUTING PTY/EON ­SELECT+ FM/AM TAPE TAPE A/B FADE MUTING DISPLAY MODE PTY / EON SELECT REC START CD /STOP REC START DUBBING TAPE A TAPE B CD / DISC SKIP + VOLUME EJECT VOLUME EJECT ­ A PLAY FULL - LOGIC CONTROL CD SYNCHRO RECORDING REC/PLAY B RM­SMXG51R REMOTE CONTROL INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LVT0692-009A [B] Warnings, Cautions and Others IMPORTANT for the U. K. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] « When a station starts broadcasting a traffic announcement, the unit automatically switches to the station. « When the program is over, the unit goes back to the previously tuned station, but the EON function still remains activated. CASE 2 If there is a station broadcasting a traffic announcement The unit tunes in the program. « When the program is over, the unit goes back to the previously tuned station, but the EON function still remains activated. CASE 3 If the FM station you are listening to is broadcasting a traffic announcement The unit continues to receive the station but the TA indicator starts flashing. « When the program is over, the TA indicator stops flashing, but the EON function still remains activated. 1 Press and hold PTY/EON. Each time you press and hold PTY/EON, "TA ON" and "TA OFF" alternately appear on the display. TA ON TA OFF PTY / EON TA ON: Switches to a traffic announcement, if any. TA OFF: This function is canceled. More about the EON function · EON data sent from some stations may not be compatible with this unit. · While listening to a program tuned in by the EON function, the station does not change even if another network station starts broadcasting a program of the same EON data. · The EON function is canceled when you change the source to CD, TAPE, or AUX, while it is temporarily canceled when you change the source to MW or LW. ­ 13 ­ Playing Back CDs This unit has been designed to playback the following CDs: Audio CD, CD-R, and CD-RW. Continued use of irregular shape CDs (heart-shape, octagonal, etc. ) can damage the unit. When playing a CD-R or CD-RW User-edited CD-Rs (Recordable) and CD-RWs (Rewritable) can be played back only if they are already "finalized. " · You can play back your original CD-Rs or CD-RWs recorded in music CD format. (However, they may not be played back depending on their characteristics or recording conditions. ) · Before playing back CD-Rs or CD-RWs, read their instructions or cautions carefully. · Some CD-Rs or CD-RWs may not be played back on this unit because of their disc characteristics, damage or stain on them, or if the player's lens is dirty. (This is caused by the fact that the reflectance of CD-RWs is lower than for regular CDs. ) Disc number Disc indicator Disc marker Continued About the disc indicators Each disc indicator corresponds to the disc tray of the same number. · The disc marker lights up for the disc number you have selected. · The disc indicator rotates while the corresponding CD is being played. · The disc indicator goes off when the unit has detected that there is no CD on the corresponding disc tray. Playing Back the Entire Discs -- Continuous Play You can play CDs continuously. 1 Load CDs. Loading CDs 1 Press 0. The unit automatically turns on and the carrousel comes out. 2 Press one of the disc number buttons (CD1, CD2 or CD3) for the disc you want to play. CD play starts from the first track of the selected disc. Track number of the currently playing disc is flashing. (Track numbers exceeding 16 are not displayed. ) 2 Place one or two discs correctly on the front slots of the carrousel, with its label side up. CORRECT INCORRECT · When using a CD single (8 cm), place it on the inner circle of the disc tray. Track number Elapsed playing time 3 If you wish to load a third disc, press DISC CHANGE on the unit or DISC SKIP on the remote control. The carrousel rotates by 120°. DISC CHANGE · Pressing CD 6 instead of the disc number buttons starts playing back if a CD is on the tray. When you turn on the unit, ALL DISC indicator lights up on the display automatically. If you do not want all the CDs to play back, select 1 DISC by pressing REPEAT. ALL DISC 1 DISC REPEAT 1 DISC SKIP 4 Press 0 again. The carrousel closes. REPEAT ALL DISC REPEAT 1 DISC ALL DISC: 1 DISC: Plays all loaded CD. To remove the disc, press 0. ­ 14 ­ CD playback sequence (when ALL DISC is selected) When 3 CDs are loaded on the disc trays, they are played in one of the following sequences. · When CD1 is pressed : CD1 ] CD2 ] CD3 (then stops) · When CD2 is pressed : CD2 ] CD3 ] CD1 (then stops) · When CD3 is pressed : CD3 ] CD1 ] CD2 (then stops) * When only 2 CDs are loaded, they are played in the same order, but the disc tray without a CD is skipped. Programming the Playing Order of the Tracks -- Program Play You can arrange the order in which the tracks play before you start playing. [. . . ] Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way -- switch off, withdraw the mains plug and consult your dealer. DON'T remove any fixed cover as this may expose dangerous voltages. DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. [. . . ]