User manual JVC LT-32C50BU

[. . . ] ENGLISH DEUTSCH FRANAIS NEDERLANDS CASTELLANO ITALIANO PORTUGUS LT-32C50BU LT-26C50BU LT-32C50SU LT-26C50SU WIDE LCD PANEL TV 16:9 LCD TV TELEVISEUR A ECRAN LCD PANORAMIQUE BREEDBEELD LCD TV TELEVISOR CON PANEL LCD PANORMICO TV LCD WIDESCREEN TELEVISOR COM ECR PANORMICO DE CRISTAL LQUIDO INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI INSTRUES Thank you for buying this JVC LCD flat television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. ("LCD" stands for Liquid Crystal Display. ) WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down. ENGLISH WARNING The TV may fall causing injuries. [. . . ] If you set the DigiPure effect too high on a low-quality picture that contains a lot of noise, this may actually make the noise worse. Picture motion compensation function: This function displays fast-moving pictures (for example, the players or ball in a football game) more smoothly and naturally on the screen. The effect level of the picture motion compensation function cannot be changed. The effect level is the same no matter which of the AUTO, MIN or MAX settings is used. OK D1015-EN DIGITAL VNR The DIGITAL VNR function cuts down the amount of `noise' (`snow' or interference) in the original picture. You can choose from the three DIGITAL VNR function settings of AUTO, MIN and MAX. AUTO(LOW)/AUTO(HIGH): The TV will automatically adjust the level of the DIGITAL VNR effect to match the amount of noise in the picture, giving you the best possible picture. If you set the DIGITAL VNR effect too high it can make the picture less sharp. If you set the DIGITAL VNR function to AUTO(LOW) but still notice some noise, change the setting from AUTO(LOW) to AUTO(HIGH). 30 PICTURE menu AUTO: The TV will automatically adjust the level of the DigiPure effect to match the amount of noise in the picture, giving the best possible picture. When you set the Super DigiPure function to AUTO and notice some noise, change the setting from AUTO to MIN. The MIN setting is not suitable for highquality pictures which contain very little noise. If you set the Super DigiPure function to AUTO but feel that the original picture quality has not been reproduced fully, change the setting from AUTO to MAX. The MAX setting is not suitable for lowquality pictures which contain a lot of noise. OFF: The Super DigiPure function is turned off. COLOUR MANAGEMENT This TV supports the COLOUR MANAGEMENT function to ensure dull colours are compensated to produce natural hues. Set this function to ON under normal conditions. ENGLISH PICTURE MANAGEMENT The PICTURE MANAGEMENT function makes it easier to see the dark areas when a picture has many dark areas, and makes it easier to see the bright areas when a picture has many bright areas. OFF: PICTURE MANAGEMENT function is turned off. MOVIE THEATRE The MOVIE THEATRE function displays a cinema film picture more smoothly and naturally on the screen. AUTO: The television automatically recognizes the type of signal and turns the function on and off. OFF: This function is turned off. 31 PICTURE menu COLOUR SYSTEM The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. Then press the a or 3 button The sub-menu of the COLOUR SYSTEM function appears. >> COLOUR SYSTEM MAIN PAL SUB AUTO The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3. 58 or NTSC 4. 43. COLOUR SYSTEM cannot be chosen when you are watching the EXT-4 picture or PC picture. 4:3 AUTO ASPECT You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). [. . . ] When you want to resume the previous ZOOM mode, press the c button again. It takes a short period of time from the time an operation such as changing channels is performed until an image is displayed. This is the time needed for the image to stabilize before it can be displayed. The TV may make a crackling sound due to a sudden change in temperature. [. . . ]