User manual JVC LT-32A61BJ INSTALLATION MANUAL

[. . . ] LT-32A61BJ LT-32A61SJ LT-26A61BJ LT-26A61SJ WIDE LCD PANEL TV INSTRUCTIONS Warning DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adaptor or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If a new mains plug has to be fitted, then follow the instruction given below: Important Do not make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow. [. . . ] 2 : lower 3 : higher D0014-EN · While the PICTURE menu is displayed, pressing the blue button will set the BRIGHT-1, CONTRAST, BRIGHT-2, SHARP, COLOUR, HUE settings to their default settings. · When watching the picture from EXT-1 to EXT-4 or the PC, picture effect settings can be memorised for each external input by setting the picture effects in the PICTURE menu. DIGITAL VNR COLOUR SYSTEM The last setting made for each item is memorised. BRIGHT-2 You can adjust the picture brightness. 2 : darker 3 : brighter SHARP You can adjust the picture sharpness. 2 : reddish 3 : greenish · You can change the HUE setting (picture hue) when the colour system is NTSC 3. 58, or NTSC 4. 43. PICTURE MODE You can choose one of three PICTURE MODEs to adjust the picture settings automatically. SOFT: Softens contrast and sharpness. COLOUR TEMP. You can select one of three COLOUR TEMP. modes (three tones of white) to adjust the white balance of the picture. Since white is the colour which is used as a reference for all the other colours, changing the COLOUR TEMP. mode affects the appearance of all the other colours on the screen. 25 PICTURE menu COOL: A bluish white. Using this mode when watching bright pictures allows you to enjoy a more vivid and bright picture. Using this mode when watching films allows you to enjoy colours that are characteristic of films. COLOUR SYSTEM The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. Then press the a or 3 button The sub-menu of the COLOUR SYSTEM function appears. >> COLOUR SYSTEM FEATURES Choose FEATURES and press the a or 3 button to display the sub-menu. OK AUTO > FEATURES D0016-EN DIGITAL VNR COLOUR SYSTEM 4:3 AUTO ASPECT AUTO(LOW) OK D1015-EN DIGITAL VNR The DIGITAL VNR function cuts down the amount of `noise' (`snow' or interference) in the original picture. OFF: This function is turned off. 2 Press the 6 buttons to choose the appropriate colour system. Then press the a button PAL: PAL system SECAM: SECAM system NTSC 3. 58: NTSC 3. 58 MHz system NTSC 4. 43: NTSC 4. 43 MHz system AUTO: This function detects a colour system from the input signal. You can only use this when you are viewing a picture from programme number PR 0 (AV), or an EXT terminal. · The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. · When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3. 58 or NTSC 4. 43. · COLOUR SYSTEM cannot be chosen when you are watching the PC picture. 26 PICTURE menu 4:3 AUTO ASPECT You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Choose 4:3 AUTO ASPECT then press the a button >> 4:3 AUTO ASPECT PANORAMIC REGULAR 14:9 ZOOM OK D0017-EN 2 Press the 6 buttons to choose a ZOOM mode 27 SOUND menu SOUND STEREO/ BASS TREBLE BALANCE 3D SOUND BALANCE OFF You can adjust the volume balance between the left and right speaker. 3 : turn the right speaker's volume level up. OK 3D SOUND You can enjoy Surround sound with a "live" effect by using the 3D SOUND function. [. . . ] If not, follow the description "BASS" or "TREBLE" on page 28. · When TV channel reception is poor, it can be hard to hear stereo or bilingual sound. In this case, follow the description "STEREO / I · II" on page 28 to hear the sound more easily by changing it to a mono sound. Other issues · When the SLEEP TIMER function operates, the TV is automatically turned off. If the TV suddenly turns off, try to press the # (standby) button to turn on the TV once again. [. . . ]