User manual JVC LT-23C50BU

[. . . ] ENGLISH DEUTSCH FRANAIS ITALIANO LT-23C50BU LT-23C50SU WIDE LCD PANEL TV BREITBILD-LCD-TV TLVISEUR GRAND CRAN LCD TV A PIENO SCHERMO LCD INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS ISTRUZIONI 50059358 2004 VICTOR COMPANY OF JAPAN, LIMITED 1004MKH-VT-VT Contents For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 For your safety This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. They are of a general nature, intended to help you with all your electronic consumer products and some points may not apply to the goods you have just purchased. Some DOs and DONTs for you Air Circulation Leave at least 10cm clearance around the television to allow adequate ventilation. This will prevent the TV from overheating and consequential possible damage to the TV. [. . . ] When On is selected, the TV can only be controlled by the remote control handset. In this case the control panel buttons except " " button on the right side of the TV will not work. These modes can be chosen by pressing or button on "EXT-2 OUTPUT". Audio Out Volume As you enter the Audio Out sound menu, Volume will be the only option. or button to change Mode. You can choose Mono, Stereo or Dual (I-II) mode, only if the selected channel supports that mode. You can also change sound mode directly pressing I-II button on your remote control. In case of bilingual broadcast (Dual Sound), you can select original or dubbed language using mode option. So when somebody listens to the original language from the loudspeakers, somebody else can listen to the dubbed language from headphone. To Store The Settings In the Sound Menu, all settings are stored automatically. Feature Menu Press "MENU" button, now you are in mainmenu. Blue Back (During No Signal) The Blue Back Feature can be set by button to either On or Off or ENGLISH - 17 - To Store Settings In Feature menu all settings are stored automatically. Note: In EXT mode, you can choose NTSC 3. 58 and NTSC 4. 43 as well. Selecting Sound System Using or button on Sound System, you can change the standard to BG, DK, I, L, Lp. Selecting Fine Tuning You can use the Fine Tuning process for fine adjustment (after coarse adjustment), if you are not happy about the image on the screen. Use or button on Fine Tuning item, until getting the best image on the screen. Selecting Search To start the search process, press button for forward search or button for backward search. If a signal is found or reaches to end of the band after searching, press or buttons to continue search process. To stop the search process when you want, press or buttons at any time. Decoder (EXT-2) You can use this mode to connect any decoder to your TV. When you select Decoder(EXT-2) On, EXT-2 output will be chosen as TV mode only and any scrambled channels will be unscrambled through decoder connected your TV via EXT-2 output. Setting VCR ( Video Cassette Recorder ) Mode This item can be seen in TV, EXT-1, EXT-2, EXT-3 and EXT-4 modes. If you want to watch a VCR source from one of these modes, then it will be better to set VCR mode on. For this, while the cursor is on this item press the or buttons to set it On. If you want to watch a DVD , then you must set this item off; because DVD is not a source like a VCR and to see the picture better, you must set the VCR mode Off. Install Menu Press "MENU" button, now you are in main menu. Then enter the Inusing stall menu pressing / or OK button. In EXT mode, Install menu appears like this: You can change only Colour system and VCR. To select programme number, you can use / button or Digit Buttons Selecting Band Band, can be chosen either, C or S by or button. [. . . ] To connect your video recorder to the TV, see TV and Video Recorder section. If you want to connect more equipment to your TV, consult your dealer. Connecting Headphones Use the stereo headphone socket on the right side of your TV, to connect headphones. Connecting the PC Connect PC monitor with 15-pin PC cable to the 15-pin connector on the rear of the computer. For detail installation procedure see Installation in PC mode. TV and Video Recoder (VCR) Connect the Video Recorder to the ANT (antenna input) socket of the TV with the aerial cable. Connect the Video Recorder to the EXT-1 or EXT-2 terminal with the SCART cable, or connect it to the EXT-4 terminal with the audio and video cables. To connect to S-Video input Connect your camera or camcorder at the back side of your TV. [. . . ]