User manual JVC LT-20A60SU

[. . . ] ENGLISH DEUTSCH FRANAIS ITALIANO LT-20A60SU WIDE LCD PANEL TV LCD-TV-GERT PANNEAU LCD TELEVISEUR TV A SCHERMO LCD INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS ISTRUZIONI 2005 VICTOR COMPANY OF JAPAN, LIMITED 1004TKH-VT-VT Contents For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 For your safety This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. They are of a general nature, intended to help you with all your electronic consumer products and some points may not apply to the goods you have just purchased. Some DOs and DONTs for you Air Circulation Leave at least 10cm clearance around the television to allow adequate ventilation. This will prevent the TV from overheating and consequential possible damage to the TV. [. . . ] When Off is selected, there will be no difference in the operation of your TV. When On is selected, the TV can only be controlled by the remote control handset. In this case the control panel buttons except " " button on the right side of the TV will not work. These modes can be chosen by pressing or button on "EXT-2 OUTPUT". Audio Out Volume As you enter the Audio Out sound menu, Volume will be the only option. or button to change Mode. You can choose Mono, Stereo or Dual (I-II) mode, only if the selected channel supports that mode. You can also change sound mode directly pressing I-II button on your remote control. To Store The Settings In the Sound Menu, all settings are stored automatically. Feature Menu Press "MENU" button, now you are in mainmenu. Then enter the Feature menu pressing / or OK button. Blue Back (During No Signal) The Blue Back Feature can be set by or button to either On or Off. Sleep Timer The Sleep Timer is used to turn the TV off after a defined period of time after selecting this item. The timer can be programmed between To Store Settings In Feature menu all settings are stored automatically. ENGLISH - 17 - Install Menu Press "MENU" button, now you are in main menu. Then enter the Inusing stall menu pressing / or OK button. D hyy Qthr 7hq 8uhry 8y Tr TqTr Avr Uvt Trhpu#'!$ 9rpqr@YU!6 7B Selecting Sound System Using or button on Sound System, you can change the standard to BG, DK, I, L, Lp. Selecting Fine Tuning You can use the Fine Tuning process for fine adjustment (after coarse adjustment), if you are not happy about the image on the screen. Use or button on Fine Tuning item, until getting the best image on the screen. Selecting Search To start the search process, press button for forward search or button for backward search. If a signal is found or reaches to end of the band after searching, press or buttons to continue search process. To stop the search process when you want, press or buttons at any time. Decoder (EXT-2) In EXT mode, Install menu appears like this: You can change only Colour system and VCR. To select programme number, you can use / button or Digit Buttons Selecting Band Band, can be chosen either, C or S by or button. Selecting Channel Channel can be changed by or button or by Digit Buttons. Selecting Colour System Using or button on Colour System, you can change the colour system to PAL, SECAM or Auto. Note: In EXT mode, you can choose NTSC 3. 58 and NTSC 4. 43 as well. You can use this mode to connect any decoder to your TV. [. . . ] If you want to connect more equipment to your TV, consult your dealer. Connecting Headphones Use the stereo headphone socket on the right side of your TV, to connect headphones. Connecting the PC Connect PC monitor with 15-pin PC cable to the 15-pin connector on the rear of the computer. For detail installation procedure see Installation in PC mode. TV and Video Recoder (VCR) Connect the Video Recorder to the ANT (antenna input) socket of the TV with the aerial cable. Connect the Video Recorder to the EXT-1 or EXT-2 terminal with the SCART cable, or connect it to the EXT-4 terminal with the audio and video cables. To connect to S-Video input Connect your camera or camcorder at the back side of your TV. Connect your equipment to the TV via S-Video input at the back side by using S-Video cables. ENGLISH - 27 - Peripheral Equipment Connections 9 $ % & ' ( ) * + , 98!#W 9 Q8DIQVU @YU" @YU! [. . . ]