User manual JVC KS-FX12WT

[. . . ] 6 Tuning into a preset station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Other convenient tuner functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Scanning broadcast stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Selecting FM reception sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Preset stations are erased when the power supply to the memory circuit is interrupted (for example, during battery replacement). If you have not stored them yet, see page 5 or 6. 2 1 1 FM FM1 FM2 FM3 AM AM Select the band (FM1, FM2, FM3 or AM) you want. 2 Select the number (1 ­ 6) for the preset station you want. 7 ENGLISH Tuning into a preset station ENGLISH Other convenient tuner functions SEL MO/RND +/­ T S RPT/SCAN Scanning broadcast stations When you press RPT/SCAN while listening to the radio, station scanning starts. Each time a broadcast is tuned in, scanning stops for about 5 seconds (tuned frequency number flashes on the display), and you can check what program is now being broadcast. If you want to listen to that program, press the same button again to stop scanning. Selecting FM reception sound When an FM stereo broadcast is hard to receive: Press MO/RND while listening to an FM stereo broadcast. The sound you hear becomes monaural but reception will be improved. Lights when receiving an FM broadcast in stereo \ To restore the stereo effect, press the same button again. Changing the AM/FM channel intervals When using this unit in an area other than North or South America: When this unit is shipped from the factory, the channel intervals are set to 10 kHz for AM and 200 kHz for FM. You can change the channel intervals by following the procedure below. "CLOCK H, " "CLOCK M" or "AREA" appears on the display. "AREA EU" appears and the channel intervals are set to 9 kHz for AM and 50 kHz (for manual tuning) / 100 kHz (for searching) for FM. To reset to the factory setting, follow the above step 1 and 2, then press ­ in step 3 ("AREA US" appears on the display. ) AREA EU: Select this when used in an area other than North and South America. 8 TAPE OPERATIONS 2 1 3 ENGLISH Tape direction Listening to a tape 1 /I/ATT Turn on the power. 2 Insert a cassette. When one side of the tape reaches its end during play, the other side of the tape automatically starts playing. (Auto Reverse) 3 PROG Select the tape direction. · Press the both buttons at the same time. Each time you press the button, the tape direction changes ) and reverse ( ). Tape play stops and the cassette ejects from the cassette compartment. · You can also eject the cassette with the unit turnd off. To stop play and eject the cassette To fast-wind a tape Press either ¡ or 1. To restart playback, press ¡ or 1 lightly. 9 SOUND ADJUSTMENTS ENGLISH Turning on/off the loudness function The human ear is less sensitive to low and high frequencies at low volumes. The loudness function can boost these frequencies to produce a well-balanced sound at low volume levels. Each time you press LOUD, the loudness function turns on/off alternatively. LOUD | \ Selecting preset sound modes You can select a preset sound adjustment suitable to the music genre. Each time you press SOUND, the sound mode changes as follows. SOUND Indication SCM OFF BEAT POP SOFT For: Bass (Flat sound) Rock or disco music Light music Quiet background music 00 +2 +4 +1 Preset values Treble 00 00 +1 ­3 Loudness On On Off Off Notes: · You can adjust the preset sound mode to your preference, and store it in memory. If you want to adjust and store your original sound mode, see "Storing your own sound adjustments" on page 12. · To adjust only the bass and treble reinforcement levels to your preference, see "Adjusting the sound" on page 11. · When one of the sound modes is selected, it is shown on the display as follows: For example, when "POP" is selected. 10 You can adjust the treble/bass sound and the speaker balance. 2 1 1 Select the item you want to adjust. Indication BAS (bass) TRE (treble) FAD (Fader)* BAL (Balance) VOL (Volume) To do: Adjust the bass Adjust the treble Adjust the front and rear speaker balance Adjust the left and right speaker balance Adjust the volume Range ­6 (min. ) -- +6 (max. ) ­6 (min. ) -- +6 (max. ) R6 (rear only) -- F6 (front only) L6 (left only) -- R6 (right only) 00 (min. ) -- 50 (max. ) Note: * If you are using a two-speaker system, set the fader level to "00". 2 Adjust the level. Note: Normally the + and ­ buttons work as the volume control buttons. So you do not have to select "VOL" to adjust the volume level. 11 ENGLISH Adjusting the sound ENGLISH Storing your own sound adjustments You can adjust the sound modes (BEAT, POP, SOFT: see page 10) to your preference and store your own adjustments in memory. 3 2 2 1, 4 1 2 SOUND Call up the sound mode you want to adjust. Within 5 seconds See page 10 for details. To adjust the bass or treble sound level Select "BAS" or "TRE. " LOUD To turn on or off the loudness function Within 5 seconds Each time you press LOUD, the loudness function turns on and off alternatively. [. . . ] Press the reset button of the CD changer. · "RESET 8" appears on the display. This unit is not connected to a CD changer correctly. · "RESET 1-RESET 7" appears on the display. The built-in microcomputer may function incorrectly due to noise, etc. While holding SEL, press for more than 2 seconds to reset the unit. (The clock setting and preset stations stored in memory are erased. ) (See page 18). 19 ENGLISH What appears to be trouble is not always serious. Check the following points before calling a service center. SPECIFICATIONS ENGLISH AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 40 watts per channel Rear: 40 watts per channel Continuous Power Output (RMS): Front: 16 watts per channel into 4 , 40 to 20, 000 Hz at no more than 0. 8% total harmonic distortion. [. . . ]