User manual JVC KD-SH909

[. . . ] CD RECEIVER KD-SH909/KD-SH707 RECEPTOR CON CD KD-SH909/KD-SH707 RECEPTEUR CD Detachable ATT ANGLE EQ KD-SH909/KD-SH707 KD-SH909 EB MOSFET 200W E-BASS D DISP B BAND M MODE KD-SH909 ATT CD MP3 INPUT DAB DISC FM PRESET PRESET AM RD CH DISC KD-SH707 EB MOSFET 200W E-BASS AUX SEL VOLUME D DISP B BAND M MODE KD-SH707 ATT MP3 INPUT RM-RK100 · This unit is equipped with the display demonstration. · Esta unidad está equipada con demostración en la pantalla. · Cet appareil est équipé d'une fonction de démonstration des affichages. Pour l'annuler, référezvous à la page 9. For installation and connections, refer to the separate manual. [. . . ] (Only the directory name and file name can be shown. ) 34 You can assign names to stations, CDs, and the external components. After assigning a name, it will appear on the display when you select the source. Sources Station frequencies Maximum number of characters up to 11 characters (up to 30 station frequencies including both FM and AM) up to 32 characters (up to 40 discs) D DISP Each time you press the button, the character set changes as follows: Capital letters ( ) Small letters ( ) ) Numbers and symbols ( 4 Select a character. About the available characters, see page 43. CDs* External components up to 11 characters * You cannot assign a name to a CD Text or an MP3 disc. 5 1 Select a source you want to assign a name to. Each time you press the button, the source changes as described on page 8. Move the cursor to the next (or previous) character position. 6 7 Repeat steps 3 to 5 until you finish inputting the name. Finish the procedure while the last selected character is flashing. 2 Press and hold SEL (select) for more than 2 seconds while pressing DISP (D). D DISP To erase the input characters DISC Insert spaces using the same procedure described above. Ex. : When you select "CD" as the source Notes: · When you try to assign a name to the 41st disc, "NAME FULL" appears on the display. (In this case, delete unwanted names before assignment. ) · When the CD changer is connected, you can assign names to discs in the CD changer. These names can also be shown on the display if you insert the discs in this unit. 35 ENGLISH Assigning names to the sources 3 Select the character set you want while " " is flashing. ENGLISH Changing the control panel angle You can change the angle of the control panel to four positions. CAUTION: NEVER insert your finger in between the control panel and the unit, as it may get caught or hurt. Adjust the angle to the position you want. Each time you press the button, the panel angle changes as follows: A B D C When using the remote controller Press ANGLE repeatedly. Each time you press the button, the control panel changes its angle -- Å, i, Ç, then Î positions in sequence. To restore the control panel to its original position, Press ANGLE 5 repeatedly. Each time you press the button, the control panel changes its angle in reverse -- Î, Ç, i, then Å positions in sequence. 36 You can detach the control panel when leaving the car. When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. 1 Insert the left side of the control panel into the groove on the panel holder. Detaching the control panel Before detaching the control panel: · Be sure to turn off the power · Be sure to return the control panel to its original position 2 1 Press the right side of the control panel to fix it to the panel holder. Unlock the control panel. The control panel comes out toward you. 2 Move the control panel to the right, then pull it out of the unit. Note on cleaning the connectors: If you frequently detach the control panel, the connectors will deteriorate. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors. 3 Put the detached control panel into the provided case. Connectors 37 ENGLISH Detaching the control panel Attaching the control panel EXTERNAL COMPONENT OPERATIONS ENGLISH MP3 player, MD player, etc. EB E-BASS DISP BAND MODE MP3 INPUT MP3 INPUT* * This MP3 INPUT is not compatible with digital signals. Playing external components For KD-SH909: You can connect two external components to this unit. Connect one to the MP3 INPUT jack on the control panel, and the other to the LINE IN plugs on the rear. · To use the external component connected to LINE IN plugs on the rear, set "LINE IN" to "ON" (see page 33). · To use the external component connected to the MP3 INPUT jack on the control panel, set "AUX IN" to "ON" (see page 34). You can operate a JVC DVD player or VCR through this receiver using the number buttons on the control panel. When you operate the VCR, you have to change the operation mode of the number buttons from the DVD operation mode to the VCR operation mode. (See "To select the target component to operate through this receiver ­ KEY SEL" on page 34. ) 1 Select the external component--AUX INPUT (AUX) or LINE INPUT (LINE). When you select a source, the power automatically comes on. Each time you press the button, the source changes as described on page 8. AUX INPUT (AUX): To select the component connected to the MP3 INPUT jack on the control panel LINE INPUT (LINE): To select the component connected to the LINE IN plug 2 Turn on the connected component and start playing the source. · If connecting a JVC's DVD player or VCR, you can perform the following operations. 38 When connecting a DVD player: : Turns on and off the power. · Skips to the beginning of the next chapter when pressed briefly. · Goes back to the beginning of the current chapter when pressed briefly. Goes back to the beginning of the previous chapter when pressed consecutively. 7: Stops operations. When you select a source, the power automatically comes on. [. . . ] Usted podrá conectar un amplificador y otros equipos para mejorar el sistema estéreo de su automóvil. · Conecte el conductor remoto (azul con rayas blancas) al conductor remoto del otro equipo para poderlo controlar a través de esta unidad. · Para el amplificador: ­ Conecte los terminales de salida de línea de esta unidad a los terminales de entrada de línea del amplificador. ­ Desconecte los altavoces de esta unidad y conéctelos al amplificador. [. . . ]