User manual JVC KD-S737R

[. . . ] CD-RECEIVER RECEPTEUR CD CD-RECEIVER KD-SX838R/S737R/S707R KD-SX838R ATT BAND PROG DISC FUNC DISC PRESET 0 /ATT 40 W x 4 MO RND TP/RDS PTY SOUND 11 12 Detachable ¢ SEL 4 7 8 SSM RPT DISP CD CHANGER CONTROL 10 9 BAND CD-CH TUNER CD 5 KD-S737R 0 /ATT KS-S737R 40 W x 4 ¢ SEL 4 7 8 9 10 11 12 SSM MO RND TP/RDS PTY SOUND RPT DISP AM FM CD 5 KD-S707R 0 /ATT KS-S707R 35 W x 4 ¢ SEL 4 7 8 9 10 11 12 SSM MO RND TP/RDS PTY SOUND RPT DISP AM FM CD 5 For installation and connections, refer to the separate manual. Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Pour l'installation et les raccordements, se référer au manuel séparé. Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding. INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING VNN3832-311S [E] NEDERLANDS KS-SX838R FRANÇAIS DEUTSCH CD RECEIVER ENGLISH Position And Reproduction Of Labels Bottom panel of the main unit DANGER: Invisible laser radiation when open and interlock failed or defeated. [. . . ] (See page 25. ) Number buttons When a number button is pressed, if the station with that frequency is broadcasting a sufficiently strong signal, the receiver will tune to that frequency. When the signal strength is not sufficient for good reception, by referring to the AF list, the receiver searches for a station broadcasting the same programme with a stronger signal. If a station broadcasting the same PI code cannot be detected in one search-cycle, PI-seek tuning is released and the original preset frequency is tuned to. CT (Clock Time) When CT data is received in the RDS signal, the time is correctly renewed. · When automatic renewal of clock time is NOT required, follow the steps below. Press the SEL button for more than 2 seconds to set the preferred setting mode. Press the "­" level control button and set to "ADJ OFF". (See page 25. ) Once these steps are completed, clock time is not renewed even if the CT (Clock Time) data is received with the RDS signal. When you wish to reactivate this mode, repeat the same procedure and in Step 3 press the "+" Level Control button to set to "ADJ ON. " In the activated mode, clock time is automatically renewed when the CT data is received. Note: It takes at least 2 minutes to renew the time after receiving CT data. The station must be received for more than 2 minutes continuously, otherwise the clock time will NOT be renewed. 15 ENGLISH Display Mode Setting the main display mode. Press the SEL button for more than 2 seconds to set the preferred setting mode. (Station name (PS NAME) Ô Frequency being received (FREQ) Ô Clock time (CLOCK) Ô) (See page 25. ) Note: When the "CLOCK" mode is set, clock time remains on the main display even during playback. Display Button The DISP button is used to select the Operation (Tuner or CD) and Clock modes. Each time the button is pressed, the display changes as follows: Operation mode (Station name* = Frequency being received = PTY; or CD) = Clock time. * When the RDS or PTY signal is weak or when not tuned to an RDS or PTY station, the Station name or PTY is NOT displayed. Other convenient tuner functions MO/RND Selecting FM reception sound When an FM stereo broadcast is hard to receive: Press MO/RND (Mono/Random) while listening to an FM stereo broadcast. The sound you hear becomes monaural but reception will be improved. Lights up when receiving an FM broadcast in stereo. MO ST To restore the stereo effect, press the same button again. 16 CD OPERATIONS ENGLISH Playing a CD 1 1 Insert a disc into the loading slot. The unit turns on, draws a CD and starts playback automatically. · When a CD is inserted upside down, "NO DISC" appears on the display and the CD automatically ejects. Total playing time of the inserted disc Total track number of the inserted disc Elapsed playing time Current track Note on One-Touch Operation: When a CD is already in the loading slot, pressing CD turns on the unit and starts playback automatically. CAUTION on Volume Setting CDs produces very little noise compared with other sources. If the volume level is adjusted for the tuner, for example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the volume before playing a CD and adjust it as required during playback To stop play and eject the CD Press 0. If you change the source to AM/FM (or CD changer for KD-SX838R only), the CD play also stops (without ejecting the CD this time). [. . . ] All tracks of the current disc (or specified disc). 31 ENGLISH Selecting CD playback modes MAINTENANCE Handling CDs COMPACT This unit has been designed only to reproduce the CDs bearing the Other discs cannot be played back. DIGITAL AUDIO mark. How to handle CDs When removing a CD from its case, press down the center holder of the case and lift the CD out, holding it by the edges. When storing a CD into its case, gently insert the CD around the center holder (with the printed surface facing up). · Make sure to store CDs into the cases after use. Center holder To keep CDs clean A dirty CD may not play correctly. If a CD does becomes dirty, wipe it with a soft cloth in a straight line from center to edge. To play new CDs New CDs may have some rough spots around the inner and outer edges. [. . . ]