User manual JVC KD-S611

[. . . ] CD RECEIVER CD-RECEIVER RECEPTEUR CD CD-RECEIVER KD-S611 K D - S 6 11 COMPACT DIGITAL AUDIO For installation and connections, refer to the separate manual. Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Pour l'installation et les raccordements, se référer au manuel séparé. Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding. INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING GET0005-001A [E] NEDERLANDS FRANÇAIS DEUTSCH ENGLISH Position And Reproduction Of Labels Bottom panel of the main unit ENGLISH DANGER: Invisible laser radiation when open and interlock failed ordefeated. [. . . ] 2 Press and hold Now you can manually change the frequency while "M" is flashing. 3 Press · If you hold down the button, the frequency keeps changing (in 50 kHz intervals for FM and 9 kHz intervals for AM ­ MW/LW) until you release the button. 5 ENGLISH Storing stations in memory You can use one of the following two methods to store broadcasting stations in memory. · Automatic preset of FM stations: SSM (Strong-station Sequential Memory) · Manual preset of both FM and AM stations FM station automatic preset: SSM You can preset 6 local FM stations in each FM band (FM1, FM2, and FM3). 2 1 1 FM FM1 FM2 FM3 Select the FM band number (FM1, FM2 or FM3) you want to store FM stations into. 2 Press and hold the both buttons for more than 2 seconds. "SSM" appears, then disappears when automatic preset is over Local FM stations with the strongest signals are searched and stored automatically in the band number you have selected (FM1, FM2 or FM3). When automatic preset is over, the station stored in number button 1 will be automatically tuned in. 6 You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually. EXAMPLE: Storing an FM station of 88. 3 MHz into the preset number 1 of the FM1 band 2 3 1 1 FM Select the FM1 band. 2 Tune into a station of 88. 3 MHz. See page 5 to tune into a station. 3 Press and hold the button for more than 2 seconds. "P1" flashes for a few seconds. 4 Repeat the above procedure to store other stations into other preset numbers. Notes: · A previously preset station is erased when a new station is stored in the same preset number. · Preset stations are erased when the power supply to the memory circuit is interrupted (for example, during battery replacement). 7 ENGLISH Manual preset ENGLISH Tuning into a preset station You can easily tune into a preset station. If you have not stored them yet, see pages 6 and 7. 1 2 1 FM AM Select the band (FM1, FM2, FM3 or AM) you want. FM1 FM2 FM3 AM 2 Select the number (1 ­ 6) for the preset station you want. 8 MO/RND RPT/SCAN Scanning broadcast stations When you press RPT/SCAN while listening to the radio, station scanning starts. Each time a broadcast is tuned in, scanning stops for about 5 seconds (tuned frequency number flashes on the display), and you can check what program is now being broadcast. If you want to listen to that program, press the same button again to stop scanning. Selecting FM reception sound When an FM stereo broadcast is hard to receive: Press MO/RND (Mono/Random) while listening to an FM stereo broadcast. The sound you hear becomes monaural but reception will be improved. A Lights up when receiving an FM broadcast in stereo To restore the stereo effect, press the same button again. 9 ENGLISH Other convenient tuner functions CD OPERATIONS ENGLISH Playing a CD 0 1 1 Insert a disc into the loading slot. The unit turns on, draws a CD and starts playback automatically. · When a CD is inserted upside down, "EJECT" appears on the display and the CD automatically ejects. A A Total playing time of the inserted disc Total track number of the inserted disc Elapsed playing time Current track Note on One-Touch Operation: When a CD is already in the loading slot, pressing CD turns on the unit and starts playback automatically. CAUTION on Volume Setting CDs produces very little noise compared with other sources. If the volume level is adjusted for the tuner, for example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the volume before playing a CD and adjust it as required during playback. To stop play and eject the CD Press 0. The source changes to the tuner (you will hear the last received station). If you change the source to AM or FM, the CD play also stops (without ejecting the CD this time). · If the ejected disc is not removed for about 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (CD play will not start this time. ) · You can eject the CD even when the unit is turned off. 10 ¢ 4 Number buttons To fast forward or reverse the track Press and hold ¢, while playing a CD, to fast forward the track. Press and hold 4 , while playing a CD, to reverse the track. To go to the next track or the previous track Press ¢ briefly, while playing a CD, to go ahead to the beginning of the next track. Each time you press the button consecutively, the beginning of the next tracks is located and played back. [. . . ] To remove these rough spots, rub the edges with a pencil or ball-point pen, etc. Moisture condensation Moisture may condense on the lens inside the CD player in the following cases: · After starting the heater in the car. In this case, eject the CD and leave the unit turned on for a few hours until the moisture evaporates. CAUTIONS: · Do not insert 8cm (3 3/16") CDs (single CDs) into the loading slot. (Such CDs cannot be ejected. ) · Do not insert any CD of unusual shape ­ like a heart or flower; otherwise, it will cause a malfunction. [. . . ]