User manual JVC KD-LX30R

[. . . ] CD RECEIVER CD-RECEIVER RECEPTEUR CD CD-RECEIVER KD-LX30R SCM SEL 7 MONO 8 LOCAL 9 MODE BAND S S M DISP ATT SOURCE TP RDS PTY INT 10 RPT 11 RND 12 OFF KD-LX30R For installation and connections, refer to the separate manual. Angaben zu Einbau und Verkabelung entnehmen Sie bitte der gesonderten Anleitung. Pour l'installation et les raccordements, se référer au manuel séparé. Zie de afzonderlijke handleiding voor details aangaande het installeren en verbinden van het toestel. [. . . ] While pressing SOURCE (ATT), press and hold OFF/0 for more than 2 seconds. "NO EJECT" flashes on the display for about 5 seconds, and the CD is locked and cannot be ejected. Note: If you press OFF/0 while CD ejection is prohibited, the control panel moves down, but the CD cannot be ejected. ("NO EJECT" appears on the display. ) To move up the display panel, press ¢ or 4 . To cancel the prohibition and unlock the CD, press and hold OFF/0 for more than 2 seconds again, while pressing SOURCE (ATT). "EJECT OK" flashes on the display for about 5 seconds, and the CD is unlocked. 23 ENGLISH SOUND ADJUSTMENTS ENGLISH Adjusting the sound You can adjust the sound characteristics to your preference. 2 1 1 Select the item you want to adjust. Each time you press the button, the adjustable items change as follows: BAS (bass) (treble) TRE FADER WOOFER BALANCE BBE Range VOLUME Indication BAS TRE FADER* To do: Adjust the bass. Adjust the front and rear speaker balance. ­06 (min. ) -- +06 (max. ) ­06 (min. ) -- +06 (max. ) R06 (Rear only) -- F06 (Front only) L06 (Left only) -- R06 (Right only) BALANCE Adjust the left and right speaker balance. Adjust the volume. See "What is BBEII?" on the next page. BBE OFF, BBE 1, BBE 2, BBE 3 00 (min. ) -- 08 (max. ) 00 (min. ) -- 50 (max. ) Note: * If you are using a two-speaker system, set the fader level to "00. " 2 Adjust the level. Equalization pattern changes as you adjust the bass or treble. Note: Normally + / ­ button works as the volume control. So you do not have to select "VOLUME" to adjust the volume level. 24 The BBEII* function restores the brilliance and clarity of the original live sound in recording, broadcasts, etc. When a speaker reproduces sound, it introduces frequency-dependent phase shifting, causing high-frequency sounds to take longer to reach the ear than low frequency sounds. The BBEII function adjusts the phase relationship between the low, mid and high frequencies by adding a progressively longer delay time to the low and mid frequencies, so that all frequencies reach the listener's ears at the proper time. In addition, the BBEII function boosts low and high frequencies, which loudspeakers tend to be less efficient in reproducing, through dynamic, program-driven augmentation. When combined with the phase compensation feature, the resulting sound has a clearer, more finely detailed "live" presence. Each time you press + or ­ in step 2 on the previous page, the BBEII function changes as follows. BBE 1 BBE 2 BBE 3 BBE OFF As the number gets higher, the BBEII function becomes stronger. When shipped from the factory, the BBEII function is set to "BBE 2. " To cancel the BBEII function, select "BBE OFF. " * Under license from BBE Sound, Inc. is a trademark of BBE Sound, Inc. R 25 ENGLISH What is BBEII? ENGLISH Using the Sound Control Memory You can select and store a preset sound adjustment suitable for each playback source. (Advanced SCM) Selecting and storing the sound modes Once you select a sound mode, it is stored in memory, and will be recalled every time you select the same source. A sound mode can be stored for each of the following sources -- FM1, FM2, FM3, AM, CD and external components. · If you do not want to store the sound mode separately for each playback source, but want to use the same sound mode for all the sources, see "To cancel Advanced SCM" on page 34. "Link" indicator 2 1 1 2 Within 5 seconds Light "MODE" on the lower part of the display. The number buttons can work as different function buttons. Select the sound mode you want. Each time you press the button, the sound mode changes as follows: BEAT SOFT POP OFF · If the "Link" indicator is lit on the display (with "SCM LINK" set to "SCM LINK ON" -- see page 34), the selected sound mode can be stored in memory for the current source, and the effect applies to the current source. · If the "Link" indicator is NOT lit on the display (with "SCM LINK" set to "SCM LINK OFF"), the selected sound mode effect applies to any source. [. . . ] In this case, eject the CD and leave the unit turned on for a few hours until the moisture evaporates. CAUTIONS: · Do not insert 8cm (3 3/16") CDs (single CDs) into the loading slot. (Such CDs cannot be ejected. ) · Do not insert any CD of unusual shape ­ like a heart or flower; otherwise, it will cause a malfunction. · Do not expose CDs to direct sunlight or any heat source or place them in a place subject to high temperature and humidity. [. . . ]