User manual JVC KD-LH811

[. . . ] CD RECEIVER KD-LH811 For canceling the display demonstration, see page 9. For installation and connections, refer to the separate manual. INSTRUCTIONS GET0274-003A [EX/EU] ENGLISH Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. [. . . ] Deactivates the key-touch tone. Beep Key-touch tone Ext Input*4 External input Telephone Telephone muting Changer: [Initial]; To use a JVC CD changer, [18]. Muting1/Muting2: Select either one which mutes the sounds while using the cellular phone. · If CD or CD changer has been selected as the source, playback pauses during telephone muting. Amp Gain You can change the maximum volume level of this receiver. Amplifier gain control High PWR: [Initial]; Volume 00 ­ Volume 50 Low PWR: Volume 00 ­ Volume 30 (Select this if the maximum power of the speaker is less than 50 W to prevent them from damaging the speaker. ) Color Sel Color selection Color Set [Initial: AllSource]; You can select your favorite display color for each source (or for all sources), [37]. You can create your own colors, and select them for the display color, [38]. 00 ­ 11 [Initial: Day Color: 07, NightColor: 05] 00 ­ 11 [Initial: Day Color: 07, NightColor: 05] 00 ­ 11 [Initial: Day Color: 07, NightColor: 05] Red Green Blue *1 *2 *3 *4 Depends on the "Dimmer" setting. Cannot be selected if the source is "CD-CH" or "EXT-IN. " ENGLISH 35 ENGLISH Selecting the dimmer mode You can dim the display at night or as you set the timer. 4 Enter the Time Set screen. 1 Enter the PSM menu (see page 5). 2 Select "Dimmer. " 5 Adjust the dimmer time. 1 Set the dimmer start time. 3 Select a setting. 2 Set the dimmer end time. Auto: Dims the display when you turn on the headlights. \ Go to step 6. Off: On: 6 Finish the procedure. Time Set: Set the timer for dimmer. \ Go to step 4. 36 Changing the display color You can select your favorite display color for each source (or for all sources). Setting the display color 1 Enter the PSM menu (see page 5). 2 Select "Color Sel. " 1 Every*4 O Aqua O Sky O Sea O Leaves O Grass O Apple O Rose O Amber O Honey O Violet O Grape O Pale O User*5 O (back to the beginning) *4 The color changes every 2 seconds. *5 The user-edited colors--"Day Color" and "NightColor" will be applied (see page 38 for details). 5 Repeat steps 3 and 4 to select the 2 color for each source (except when selecting "AllSource" in step 3). 6 Finish the procedure. 3 Select the source. Ex. : When "AllSource" is selected AllSource*1 O CD O Changer (or Ext In*2) O FM O AM O DAB*3 O (back to the beginning) *1 When you select "AllSource, " you can use the same color for all the sources. *3 Selectable only when DAB tuner is connected. ENGLISH 37 4 Select the color. ENGLISH Creating your own color--User You can create your own colors--"Day Color" and "NightColor. " 5 Adjust the level (00 ­ 11) of the selected primary color. 1 Enter the PSM menu (see page 5). 2 Select "Color Set. " 6 Repeat steps 4 and 5 to adjust the other primary colors. 7 Finish the procedure. 3 Select "Day Color" or "NightColor. " Ex. : When "Day Color" is selected 4 Select the primary colors--"Red, " "Green, " or "Blue. " 38 Other main functions Assigning titles to the sources You can assign titles to CDs (both in this receiver and in the CD changer) and the external components (EXT-IN). For available characters, see page 47. Sources CDs/CD-CH* External components Maximum number of characters Up to 32 characters (up to 30 discs) Up to 8 characters 3 Move to the next (or previous) character position. * You cannot assign a title to a CD Text or an MP3/WMA disc. 4 Repeat steps 1 to 3 until you finish entering the title. 1 Select the source. · For a CD in this receiver: Insert a CD. · For CDs in the CD changer: Select "CD-CH, " then select a disc number. · For external components: Select "EXT-IN" (see page 35). 4 Finish the procedure. 2 Enter the TITLE menu (see page 5). 3 Assign a title. 1 Select a character set. To erase the entire title In step 3 on the left. . . Ex. : When you assign a title to a CD ENGLISH 39 2 Select a character. ENGLISH Changing the control panel angle Detaching the control panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. The control panel changes its angle as follows: Detaching the control panel Before detaching the control panel, be sure to turn off the power. When using the remote controller. . . . Attaching the control panel Caution: Do not insert your finger behind the control panel. 40 External component operations Playing an external component ENGLISH 41 You can connect an external component to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied). Before operating the external component, select the external input correctly (see page 35). · For connection, see Installation/Connection Manual (separate volume). Y ! Turn on the connected component and start playing the source. [. . . ] (Record MP3/WMA tracks using a compliant application. ) Skip to another track or change the disc. (Do not add the extension code <. mp3> or <. wma> to non-MP3 or WMA tracks. ) · Noise is generated. MP3/WMA Playback The track played back is not an MP3/WMA track (although it has the extension code <. mp3> or <. wma>). · Elapsed playing time is not This sometimes occurs correct. · "Not Support" appears on · Tracks are not encoded in the display and track skips. [. . . ]