User manual JVC KDDV4200J-KD-DV4200 Instruction Manual

[. . . ] DVD/CD RECEIVER Instructions Manual de Instrucciones RECEPTOR CON DVD/CD RECEPTEUR DVD/CD Manuel d'Instructions English Español Français KD-DV4200 To cancel the display demonstration, see page 5. Para cancelar la demostración en pantalla, consulte la página 5. Pour annuler la démonstration des affichages, référez-vous à la page 5. Para la instalación y las conexiones, refiérase al manual separado. [. . . ] In addition, for some discs, the initial languages settings will not work as you set due to their internal disc programming. · When you select "16:9" for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width. · Even if "4:3 PAN SCAN" is selected, the screen size may become "4:3 LETTER BOX" for some DVDs. iPod® or D. · If the text information includes more than 8 characters, it scrolls on the display (see also page 20). player, some operations may not be performed correctly or as intended. In this case, visit the following JVC web site: For iPod users: <http://www. jvc. co. jp/ english/car/support/ks-pd100/index. html> For D. player users: <http://www. jvc. co. jp/ english/car/support/ks-pd500/index. html> Title assignment · If you try to assign titles to more than 30 station frequencies, "NAMEFULL" appears. Delete unwanted titles before assignment. 27 On-screen guide icons During playback, the following guide icons may appear for a while on the monitor. DVD: Appears at the beginning of a scene containing: : Multi-subtitle languages : Multi-audio languages : Multi-angle views : : Playback Pause : DVD/VCD: Forward slow motion : DVD: Reverse slow motion : Forward search : Reverse search About sounds reproduced through the rear terminals · Through the analog terminals (Speaker out/LINE OUT): 2-channel signal is emitted. When playing a multi-channel encoded disc, multi-channel signals are downmixed. (AUDIO--DOWN MIX: see page 22. ) · Through DIGITAL OUT (optical): Digital signals (Linear PCM, Dolby Digital, DTS, MPEG Audio) are emitted through this terminal. (For more details, see table below. ) To reproduce multi-channel sounds such as Dolby Digital and DTS, connect an amplifier or a decoder compatible with these multi-channel sources to this terminal, and set "DIGITAL AUDIO OUTPUT" correctly. (See page 22. ) Output signals through the DIGITAL OUT terminal Output signals are different depending on the "DIGITAL AUDIO OUTPUT" setting on the setup menu (see page 22). DIGITAL AUDIO OUTPUT DVD STREAM/PCM Output Signals DOLBY DIGITAL/PCM 48 kHz, 16 bits stereo Linear PCM PCM ONLY 48 kHz, 16/20/24 bits Linear PCM 96 kHz, Linear PCM with DTS DTS bitstream with Dolby Digital with MPEG Audio Audio CD, Video CD Audio CD with DTS MP3/WMA 48 kHz, 16 bits stereo Linear PCM 48 kHz, 16 bits stereo Dolby Digital bitstream Linear PCM MPEG bitstream 48 kHz, 16 bits Linear PCM 44. 1 kHz, 16 bits stereo Linear PCM/48 kHz, 16 bits stereo Linear PCM DTS bitstream 44. 1 kHz, 16 bits stereo Linear PCM 32/44. 1/48 kHz, 16 bits Linear PCM 28 Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. Symptom General · Sound cannot be heard from the speakers. · SSM automatic presetting does not work. Remedy/Cause · Adjust the volume to the optimum level. · Eject the disc forcibly (see page 2). FM/AM · Static noise while listening to the radio. · Disc can be neither played back nor ejected. · Recordable/Rewritable discs cannot be played · Insert a finalized disc. · Finalize the discs with the component which you used for · Tracks on the Recordable/Rewritable discs recording. Insert the disc correctly. Disc playback · "NO DISC" appears on the display. · Sound and pictures are sometimes interrupted · Stop playback while driving on rough roads. · No playback picture (DVD/VCD) appears on the Parking brake wire is not connected properly. Installation/Connection Manual. ) · No picture appears on the monitor at all. [. . . ] *1 . Black Yellow *2 *2 To metallic body or chassis of the car To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) ( ) ( 12 ) To an accessory terminal in the fuse block Ignition switch Line out (see diagram (. ) ) Red Blue with white stripe Fuse block To the remote lead of other equipment or power aerial if any (200 mA max. ) (. 200 ) To cellular phone system To parking brake, metallic body or chassis of the car , *2 Before checking the operation of this unit prior to *2 installation, this lead must be connected, otherwise power cannot be turned on. , . Brown Light green White with black stripe White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Purple Right speaker (rear) () Left speaker (front) () Right speaker (front) () Left speaker (rear) () C Connecting the parking brake wire / When installing the monitor in a location where it can be seen by the driver , D Connecting the crimp connector / Wire connecting the battery and the parking brake switch. [. . . ]