User manual JVC KD-AHD75BT

[. . . ] · Make sure not to block the fan on the rear panel to maintain proper ventilation when installed. · You cannot install the receiver on the car which has any obstacles in the space shown in "Required space for installation" below. ( ) . · , , ", " . Required space for installation / , 20 mm 5. 5 mm 7 mm 4 mm Dashboard Caution when installing / Control panel 4 mm 7 mm Trim plate is detached on this illustration for explanation. . Fit the receiver into the mounting sleeve by using four corners of the trim plate. [. . . ] *2 . Screw (option) () Bracket *2 *2 Flat type screws (M5 x 6 mm) *2 (M5 x 6 ) *2 Bracket *2 *2 Install the receiver at an angle of less than 30°. 30°. Note : When installing the receiver on the mounting bracket, make sure to use the 6 mm-long screws. . Removing the receiver Before removing the receiver, release the rear section. . Insert the two handles, then pull them as illustrated so that the receiver can be removed. , , , . ELECTRICAL CONNECTIONS To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all electrical connections before installing the receiver. · Be sure to ground this receiver to the car's chassis again after installation. . · . Notes: · Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC : IN-CAR ENTERTAINMENT dealer. · It is recommended to connect to the speakers with maximum power of more than 50 W (both , JVC. If the maximum power is less than 50 W, change "Amp Gain" setting to prevent the speakers from being damaged (see page · 50 ( , 4 8 ). 50 , "Amp · To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape. . PRECAUTIONS on power supply and speaker connections: : · DO NOT connect the speaker leads of the power cord to the car battery; otherwise, · , the receiver will be seriously damaged. 2 Connect the colored leads of the power cord in the order specified in the illustration below. 4 Finally connect the wiring harness to the receiver. VIDEO IN (see diagram LINE IN (see diagram Rear ground terminal / . ) *1 Not included for this receiver *1 To CD changer/DAB tuner or another external component (see diagram ) -/ DAB (. ) Ignition switch Black REVERSE GEAR SIGNAL (see diagram / . ) Yellow *2 *2 To metallic body or chassis of the car To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) ( ) ( 12 ) Red Line out (see diagram ) (. ) To an accessory terminal in the fuse block Blue with white stripe Orange with white stripe Fuse block To the remote lead of other equipment or power aerial if any (200 mA max. ) (. 200 ) To car light control switch *2 Before checking the operation of this receiver prior to installation, this lead must be connected, otherwise power cannot be turned on. *2 , . Brown Light green To cellular phone system To parking brake (see diagram ) (. ) White with black stripe Gray with black stripe Left speaker (front) () White Green with black stripe Right speaker (front) () Gray Green Purple with black stripe Left speaker (rear) () Purple Right speaker (rear) () C Connecting the parking brake wire / D Connecting the back camera lead / (REVERSE GEAR SIGNAL) Connect the parking brake wire to the parking brake system built in the car. . Back lamp lead To back lamp Back lamps Purple with white stripe KD-AHD75BT REVERSE GEAR SIGNAL Parking brake Parking brake wire (light green) ( ) To metallic body or chassis of the car To car battery Back lamp lead E Connecting the crimp connector*3 / *3 Attach the parking brake wire to this point. . Parking brake switch (inside the car) ( ) Wire connecting the battery and the parking brake switch. [. . . ] Audio/video control amplifier or the decoder compatible with the multichannel digital sources / , KS-HP2 Cordless headphones (not supplied) *4 ( ) *4 External component KV-MR9010 9-INCH WIDESCREEN MONITOR (not supplied) 9- ( ) *4 To listen to disc playback sound while in Dual Zone operations (see page 40 of INSTRUCTIONS). , . You can connect amplifiers to upgrade your car stereo system. · Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this receiver. · For amplifier only: ­ Disconnect the speakers from this receiver, connect them to the amplifier. [. . . ]