User manual JVC HR-XVC16BUS-HR-XVC16 Instruction Manual

[. . . ] DVD PLAYER & VIDEO CASSETTE RECORDER HR-XVC16BU HR-XVC17SU INSTRUCTIONS LPT1126-001A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] You can easily modify your unit to respond to A or B code signal. Select Move PBC VCD On: Video CDs with PBC are played according to the PBC. Off: Video CDs with PBC are played the same way as Audio CDs. 1/ I B ENTER Auto Play DVD x You can set up the DVD+VCR so a DVD disc automatically starts playing whenever the DVD is inserted. If Auto Play mode is set to On, this DVD player will search for title that has the longest playback time and then play back the title automatically. Note: The Auto Play function may not work for some DVDs. 1-3 B. L. E. (Black Level Expansion) To select the black level of playback pictures. (7. 5 IRE cut off) · Keep pressing ENTER down during step 1. 1. Press the number Key "1" for A, "2" for B or "3" for C to change the remote control code. Press 1/ I on the unit to turn off the unit with no video-tape inserted. The code currently set on the remote control blinks on the front display panel for approximately 5 seconds, and is applied to the unit. 19 Preparation Set Playback Control (PBC) to On or Off. Operation This chapter describes how to operate the VCR and DVD. Manual Tracking To manually adjust the tracking use the CH -/+ buttons during playback. Notes: · · Vertical jitter requires a very fine adjustment. Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 seconds. VCR Tape Pla ybac k Press the VCR button to select the device to be operated. Basic Instructions 1. Tune the TV to the DVD+VCR output channel (CH 3 or 4) or if a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV's source selector to VIDEO. If the (TIMER) indicator in the display window is lit press POWER 1/: once. If a tape without a safety tab is inserted the unit starts playback automatically. If the tape reaches the end before you press STOP (x) the DVD+VCR automatically stops, rewinds and ejects the tape. Notes: · It is not necessary to select the tape speed for playback because it is automatically selected by the DVD+VCR. Also, during playback the TV/VCR selector switches to VCR mode automatically. Search This function lets you visually search for a tape section in either direction: forward and reverse. During the high-speed picture search modes, the audio is muted and horizontal lines (noise bars) appear. Also, a short time is needed to stabilize the tape speed when re-entering the PLAY mode so slight interference may be observed during this time. Notes: · After 3 minutes in SEARCH mode the DVD+VCR returns to PLAY mode to protect the tape and video heads. During the tape fast rewinding (backward or forward), don't press the same button (REW or FF) again. Otherwise it takes more time to rewind the tape. · Still Picture and Frame-by-Frame Playback 1. [. . . ] · The total number of contents on the disc should be less than 1500 files and 300 folders. · Some discs may be incompatible due to a different recording format or the condition of disc. · Ensure that all the selected files have the ". jpg" extensions when copying into the CD layout. · If the files have ". jpe" or ". jpeg" extensions, please rename them as ". jpg" file. [. . . ]