User manual JVC HR-S7722

[. . . ] CONTENTS SAFETY FIRST 2 VIDEO CASSETTE RECORDER Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 QUICK SET UP GUIDE 5 HR-S7700EK HR-S7722EK TV TV/VCR AUDIO ­ ­:­ ­ CHECK THE CONTENTS . . . . . . . . . . . . . . . . . . 9 T-V LINK SATELLITE RECEIVER CONTROL BASIC OPERATIONS 11 12 14 T-V Link Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 20 ADVANCED OPERATIONS 24 1 4 VPS/PDC 2 5 8 AUX 3 2 6 9 4 DAILY/QTDN. [. . . ] When the recorder is in Stop mode or recording, press TV/VCR on the remote control to turn off the VCR indicator on the display panel. If you turn on the recorder when the satellite receiver's power is off, nothing appears on the TV screen. In this case, turn on the satellite receiver, or set the TV to its TV mode, or press TV/VCR on the remote control to set the recorder to the video mode. NOTE: Refer to the instructions supplied with your satellite receiver. 31 Before performing the following steps: Make sure the satellite receiver is connected to the recorder's AV2 (L-2) IN/DECODER connector. Insert a cassette with the safety tab in place. 1 SA T ACCESS MAIN MENU SCREEN Press MENU. ATTENTION Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on. If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on. Auto Satellite Prog recording and timer-recording cannot be done at the same time. When you press and hold the recorder's SAT button to engage the Auto Satellite Prog Rec mode, if the SAT button does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*. If this is the case, perform "Express Timer Programming" ( pg. 20) to timer-record a satellite programme. * Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers. 2 3 4 5 ACCESS OUTPUT/INPUT SET SCREEN Move the highlight bar (pointer) to "OUTPUT/INPUT SET" by pressing %fi, then press OK or #. SELECT L-2 SELECT MODE Move the highlight bar (pointer) to "L-2 SELECT", by pressing %fi, then press OK or # to set to "SAT" or "A/V". Then press MENU. OUTPUT/INPUT SET L-1 OUTPUT L-1 INPUT L-2 SELECT L-2 INPUT VIDEO VIDEO SAT VIDEO [5] = [MENU] : EXIT SET TAPE SPEED Press SP/LP ( ) to set the tape speed. ENGAGE AUTO SATELLITE PROG REC MODE Press and hold SAT for about 2 seconds. If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode. NOTES: Auto Satellite Prog recording is possible with the AV2 (L-2) IN/DECODER connector only. When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON". After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver. Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer. The SAT button blinks while Auto Satellite Prog recording is in progress. Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode. If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording. Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme. If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the SAT button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording. [. . . ] 14 and "Operating JVC TVs" on page 63 3 REVIEW Button "reviews" timer-recorded programme. 19, 21 * VPS (Video Programme System) recording is not currently available in the U. K. and not possible with this recorder. TV TV/VCR AUDIO ­ ­:­ ­ 1 4 VPS/PDC 2 5 8 AUX 3 2 6 9 4 DAILY/QTDN. WEEKLY/HEBDO 7 0000 0 START DEBUT STOP FIN DATE PR 6 7 8 9 0 EXPRESS 1 PROG ? 30 SEC MENU ENTER/EN TRE E 3 OK TV PR + ­ TV PR ­ TV ! [. . . ]