User manual JVC HR-S5800E safety instructions

[. . . ] 07470 Telephone Number :973-315-5000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Failure to heed the following precautions may result in damage to the VCR, Remote or video cassette. 1. [. . . ] (The PlusCode programing numbers are the numbers next to the program in most TV listing. ) 1 Load a cassette Make sure the record safety tab is intact. The VCR turns on, and the counter is reset, automatically. 1 2 Access VCR Plus+ screen VCR PLUS+ Press PROG. The clock must be set to access the VCR PRESS NUMBER KEY (09) Plus+ screen. PRESS (+/) TO SET EXPRESS PROGRAMMING If you have not set the PRESS (PROG. ) TO END clock, the Main Menu screen appears after an error message is displayed. Refer to page 8 for the Plug & Play setting or page 10 for the clock setting procedure. VCR TV CABLE/DBS POWER 1 4 2 5 8 0 3 6 9 34 WEEKLY DAILY (M-F) CANCEL STOP +/ 7 27 4 8 4 6 3 Enter PlusCode number Press the appropriate Number keys to input the PlusCode number printed in the TV listings for the TV broadcast you wish to record, then press OK. VCR PLUS+ 123 PRESS NUMBER KEY (09) THEN (OK) PRESS (PROG. ) TO END 347 Then; If the Guide Channel Set screen appears -- go to step 4. To make corrections, press CANCEL and input the correct PlusCode number. EN 39 4 Input receiving channel number The guide channel GUIDE CHANNEL SET number, which is GUIDE CH: 12 assigned to the TV or VCR CH : cable station for the PlusCode number that PRESS NUMBER KEY (09) you entered in step 3, OR (5, ), THEN (OK) PRESS (PROG. ) TO END will appear automatically on the Guide Channel Set screen. Press the Number keys (or CH +/ or %fi) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box, then press OK. The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously. If you receive your channels with a cable box and if you have properly set your Controller, "CABLE CH" appears in place of "VCR CH". If not, refer to pages 16 19. 7 Return to normal screen Press PROG. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. Read the following information carefully. 25 16 25 VCR Plus+ guide channel matching The VCR Plus+ programing system assigns a VCR Plus+ guide channel to the TV channels and the cable channels. These guide channel numbers are also called the VCR Plus+ channel codes. Most TV listings have a section, usually a chart, indicating the guide channel numbers assigned to each station. For accurate VCR Plus+ programing, the VCR Plus+ guide channel number for each station should match the channel number on which it is received in your area. NOTES: VCR TV CABLE/DBS 1 4 7 2 5 8 0 3 6 9 In many instances, the VCR Plus+ guide channel numbers for cable and broadcast TV stations DO NOT match the channel number on which it is received by your VCR or cable box. Check your TV listing, or contact your cable supplier for details. 45 25 16 25 EN 41 1 Access Main Menu screen 2 Access Initial Set screen Press MENU. On the front panel: Press CH5 to move the highlight bar (arrow) to "INITIAL SET", then press OK. 5 Input receiving channel number MAIN MENU FUNCTION SET TUNER SET = INITIAL SET REC LEVEL CTL VIDEO NAVIGATION PRESS (5, ), THEN (OK) PRESS (MENU) TO END On the front panel: Press CH5 to select the number of the channel on which the guide channel's broadcasts are received, then press OK. (Ex. ) If WNJU(Ind. ) is received on channel 47 GUIDE CHANNEL SET GUIDE CH : 6 VCR CH : 47 On the Remote: Press %fi to move the highlight bar (arrow) to "INITIAL SET", then press OK or #. 3 Access Guide Channel Set screen On the front panel: Press CH5 to move the highlight bar (arrow) to "GUIDE CHANNEL SET", then press OK. INITIAL SET CLOCK SET LANGUAGE ENGLISH = GUIDE CHANNEL SET CABLE BOX SET DBS RECEIVER SET JLIP ID NO. SET SELECT WITH (5, ) AND (OK) PRESS (MENU) TO END PRESS NUMBER KEY (0-9) On the Remote: OR (5, ), THEN (OK) PRESS (MENU) TO END Press the Number keys or %fi to input the number of the channel on which the guide channel's broadcasts are received, then press OK or #. Repeat steps 4 and 5 for each instance. 6 Return to normal screen Press MENU. On the Remote: Press %fi to move the highlight bar (arrow) to "GUIDE CHANNEL SET", then press OK or #. 4 Input guide channel number On the front panel: Press CH5 to select (Ex. ) When inputting the guide channel number 6 the VCR Plus+ guide for WNJU(Ind. ) channel number as shown in the TV listing, GUIDE CHANNEL SET then press OK. GUIDE CH : 6 VCR CH : On the Remote: Press the Number keys or %fi to input the VCR PRESS NUMBER KEY (0-9) OR (5, ), THEN (OK) Plus+ guide channel PRESS (MENU) TO END number as shown in the TV listing, then press OK or #. If you receive your channels with a cable box and if you have properly set your Controller, "CABLE CH" appears in place of "VCR CH". If not, refer to pages 16 19 and re-perform the procedure. 42 EN TIMER RECORDING (cont. ) You can directly program the VCR's timer to record up to 8 broadcasts, as far as a year in advance. Remember, the clock must be set before you can program the timer ( pg. [. . . ] Enclose, with the unit, a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit. Print your home return address on the outside and the inside of the carton. Send to the appropriate JVC Factory Service Center as listed above. Don't service it yourself. CAUTION To prevent electrical shock, do not open the cabinet. Refer servicing to qualified service personnel. ACCESSORIES To purchase accessories for your JVC product, you may contact your local JVC Dealer. [. . . ]