User manual JVC HR-S5500E service manual contents

[. . . ] 19 RECORDING 23 Basic Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 TIMER RECORDING SHOWVIEW® Timer Programming . . . . . . . . . . . . . . . . 30 Automatic Satellite Programme Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 28 EDITING 35 Edit From A Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] B Select the programme to modify. Press rt, then press OK or e. Overlapping programmes blink on the TV screen. You can only select one of the overlapping programmes. NOTE: If you do not mind this overlap, press PROG to finish the timer programme setting. The programme with the lower programme number will be recorded and the other one will not be recorded correctly. If no changes are made for approximately 1 minute, the recorder will return to the normal screen. To cancel a programme, press & when the Programme screen you do not want is shown. "PROGRAM COMPLETED" appears on the TV screen for about 5 seconds, then the normal screen appears. To change a programme, press the appropriate button: START+/­, STOP+/­, DATE+/­, PR+/­, VPS/PDC and/or SP/LP (p) when the Programme screen on which you want to make changes is shown, then press OK. "PROGRAM COMPLETED" appears on the TV screen for about 5 seconds, then the normal screen appears. C Cancel or change programme setting. NOTE: If the overlap is not yet solved, or another overlap occurs with the timer programme setting after making the last correction on a programme, the conflicting programmes will be shown on the Programme Check screen again. Repeat the above steps again until the overlap is solved. 34 EN TIMER RECORDING (cont. ) ATTENTION Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on. If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance's power is turned on. Automatic Satellite Programme Recording and timerrecording cannot be done at the same time. Automatic Satellite Programme Recording This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder's AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. 20). EDITING EN 35 Edit From A Camcorder A If the camcorder has no S-VIDEO output connector . . . Your recorder You can use a camcorder as the source player and your recorder as the recorder. A Make connections. A If the camcorder has no S-VIDEO output connector . . . connect the camcorder's AUDIO OUT and VIDEO OUT connectors to the recorder's front panel AUDIO and VIDEO input connectors. connect the camcorder's AUDIO OUT and S-VIDEO OUT connectors to the recorder's front panel AUDIO and S-VIDEO input connectors. When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder. AUDIO input VIDEO input Audio cable (not provided) Video cable (not provided) VIDEO OUT Press AUX (NUMBER key "0") and/or PR to select "F-1" for the AUDIO and VIDEO input connectors, or "S-1" for the AUDIO and S-VIDEO input connectors, depending on the connectors being used. B Set the recorder's input mode. C Set the edit mode. See "PICTURE CONTROL" on page 45. Camcorder D Start the camcorder. AUDIO OUT Engage the Play mode of the camcorder. Player E Start the recorder. NOTES: Your recorder Engage the Record mode of the recorder. B If the camcorder has an S-VIDEO output connector . . . All necessary cables can be obtained from your dealer. When you select "EDIT" to dub tapes in step 3, be sure to select "AUTO" (or "NORM" when "B. E. S. T. " is set to "OFF") after you finish dubbing the tapes. S-VIDEO input AUDIO input Audio cable (not provided) S-Video cable (not provided) S-VIDEO OUT Camcorder AUDIO OUT Player 36 EN EDITING (cont. ) Output/Input Set L-1 OUTPUT and L-1 INPUT Setting Set "L-1 OUTPUT" and "L-1 INPUT" to the appropriate mode depending on the type of appliance connected to the recorder's AV1 (L-1) IN/OUT connector. A Access the Main Menu screen. Press MENU. B Access the Output/Input Set screen. Press rt to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or e. the output or input C SelectIN/OUT connector. mode for the AV1 (L-1) Press rt to move the highlight bar (pointer) to "L-1 OUTPUT" or "L-1 INPUT". Then, press OK or e to select the appropriate setting. * The default setting is bold in the table below. 8 L-1 OUTPUT VIDEO: S-VIDEO: If a connected appliance's input is compatible only with regular video signals, set to "VIDEO". If a connected appliance's input is compatible with Y/C signals, set to "S-VIDEO". If a connected appliance's output is compatible only with regular video signals, set to "VIDEO". If a connected appliance's output is compatible with Y/C signals, set to "S-VIDEO". You can obtain highquality S-VHS picture. 8 L-1 INPUT VIDEO: S-VIDEO: D Return to the normal screen. Press MENU. NOTES: If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-1 INPUT" to "S-VIDEO". [. . . ] 15 Set Stations (A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Set Stations (B). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Skip Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 47 S-VHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]