User manual JVC HR-J670

[. . . ] CONTENTS VIDEO CASSETTE RECORDER SAFETY FIRST 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 HR-J670EK HR-J672EK HR-J470EK HR-J270EK TV TV/VCR AUDIO ­ ­:­ ­ QUICK SET UP GUIDE 4 CHECK THE CONTENTS . . . . . . . . . . . . . . . . . . 7 T-V LINK SATELLITE RECEIVER CONTROL BASIC OPERATIONS 9 10 12 T-V Link Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 ADVANCED OPERATIONS 22 1 4 VPS/PDC 2 5 8 AUX 3 2 6 9 4 DAILY/QTDN. [. . . ] Connect a satellite receiver to the recorder's AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver; the recorder starts recording when the signals input from the satellite receiver to the AV2 (L-2) IN/DECODER connector, and when there is no input signals the recorder stops recording and the power shuts off. Outdoor Unit Aerial 21-pin AV input connector (SCART) Back of TV Satellite Cable TV Aerial cable Aerial connector Satellite Receiver Unit ANT. IN DECODER VCR TV RF OUT EXT. 2 EXT. 1 Mains outlet CONTROLEUR SAT ENTREE ANT. IN AV2 ENTREE/DECODEUR IN/DECODER (L-2) AV1 ENTREE/SORTIE IN/OUT AUDIO (L-1) SAT CONTROL SORTIE OUT ANTENNE SORTIE RF OUT R L Back of Recorder IMPORTANT When you set "L-2 SELECT" to "SAT" ( pg. 32), it is possible to view a satellite broadcast with the TV set to its AV mode even if the recorder is turned off. When the recorder is in Stop mode or recording, press TV/VCR on the remote control to turn off the VCR indicator on the display panel. If you turn on the recorder when the satellite receiver's power is off, nothing appears on the TV screen. In this case, turn on the satellite receiver, or set the TV to its TV mode, or press TV/VCR on the remote control to set the recorder to the video mode. NOTE: Refer to the instructions supplied with your satellite receiver. 27 Before performing the following steps: Make sure the satellite receiver is connected to the recorder's AV2 (L-2) IN/DECODER connector. Insert a cassette with the safety tab in place. SP/LP SA SAT indicator ATTENTION Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on. If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on. Auto Satellite Prog recording and timer-recording cannot be done at the same time. When you press and hold the recorder's SAT button to engage the Auto Satellite Prog Rec mode, if the SAT indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*. If this is the case, perform "Express Timer Programming" ( pg. 18) to timer-record a satellite programme. * Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers. 1 2 3 ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Move the highlight bar (pointer) to "MODE SET" by pressing %fi, then press OK or #. T SELECT L-2 SELECT MODE Move the highlight bar (pointer) to "L-2 SELECT", by pressing %fi, then press OK or # to set to "SAT" or "L-2". ON DIRECT REC ON AUTO SP=LP TIMER OFF POWER SAVE OFF NEXT PAGE [5] = [MENU] : EXIT PREVIOUS PAGE L-2 SELECT SAT [5] = [MENU] : EXIT 4 5 SET TAPE SPEED Press SP/LP ( ) to set the tape speed. ENGAGE AUTO SATELLITE PROG REC MODE Press and hold SAT for about 2 seconds. If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode. NOTES: Auto Satellite Prog recording is possible with the AV2 (L-2) IN/DECODER connector only. When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON". After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver. Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer. The SAT indicator blinks while Auto Satellite Prog recording is in progress. [. . . ] 12 and "Operating JVC TVs" on page 55 3 REVIEW Button "reviews" timer-recorded programme. 17, 19 * VPS (Video Programme System) recording is not currently available in the U. K. and not possible with this recorder. TV TV/VCR AUDIO ­ ­:­ ­ 1 4 VPS/PDC 2 5 8 AUX 3 2 6 9 4 DAILY/QTDN. WEEKLY/HEBDO 7 0000 0 START DEBUT STOP FIN DATE PR 6 7 8 9 0 EXPRESS 1 PROG ? 30 SEC MENU ENTER/EN TRE E 3 OK TV PR + ­ TV PR ­ TV ! [. . . ]