User manual JVC HR-J665

[. . . ] VIDEO CASSETTE RECORDER CONTENTS SAFETY FIRST 2 4 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . 3 HR-J665EK HR-J660EK HR-J665ES TV TV/VCR AUDIO ­ ­:­ ­ QUICK SET UP GUIDE CHECK THE CONTENTS . . . . . . . . . . . 6 BASIC OPERATIONS 8 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ADVANCED OPERATIONS 17 1 4 VPS/PDC 2 5 8 AUX 3 2 6 9 4 DAILY/QTDN. [. . . ] When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*. If this is the case, perform "Express Timer Programming" ( pg. 14) to timer-record a satellite programme. Auto Satellite Prog Recording is not possible with those satellite receivers. q q q q q q q q q q Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only. When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON". After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver. Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer. The REC LINK indicator blinks while Auto Satellite Prog recording is in progress. Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode. If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programmes for Auto Satellite Prog recording. Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme. If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording. You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN/DECODER connector. 24 ADVANCED OPERATIONS (cont. ) You can use your video recorder as the source player or as the recording deck. Edit To Or From Another 1 Video Recorder . MAKE CONNECTIONS Connect the player's 21-pin SCART connector to the recorder's 21-pin SCART connector as illustrated on the below. connect its AV2 IN/DECODER or AV1 IN/OUT connector to the source player. 1 4 7 AUX 2 5 8 0 3 2 6 9 4 2 TV PROG SET RECORDING DECK'S INPUT MODE Set to AUX. With this video recorder, press AUX and/or TV PROG to select "L-1" for the AV1 IN/OUT connector, or "L-2" for the AV2 IN/DECODER connector, depending on the connector being used. 1 ? 3 3 4 5 q q q SET EDIT MODE See "Picture Control" on page 20. START SOURCE PLAYER Engage its Play mode. START RECORDING DECK Engage its Record mode. NOTES: All necessary cables can be obtained from your dealer. When you select EDIT to dub tapes in step 3, be sure to select AUTO (or NORM when B. E. S. T. When you use this recorder as the player for editing, be sure to set "O. S. D. " to "OFF" before starting ( pg. 26). Recorder Your recorder TV Receiver TV Receiver Player Your recorder ENTREE ANT. IN AV2 ENTREE/DECODEUR IN/DECODER AV1 ENTREE/SORTIE IN/OUT AUDIO SORTIE OUT R ANTENNE SORTIE RF OUT AV2 ENTREE/DECODEUR IN/DECODER AV1 ENTREE/SORTIE IN/OUT AUDIO SORTIE OUT R ANTENNE SORTIE RF OUT L L VIDEO CHANNEL or AV mode 21-pin SCART Cable (not provided) 21-pin SCART Cable (not provided) RF Cable (provided) RF Cable (provided) Another recorder Recorder Player Another recorder VIDEO CHANNEL or AV mode 25 Edit From A Camcorder 1 4 7 AUX You can use a camcorder as the source player and your video recorder as the recorder. 1 2 3 4 5 q q MAKE CONNECTIONS Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's front panel AUDIO/VIDEO input connectors. q When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder. 2 5 8 0 3 2 SET RECORDER'S INPUT MODE Press AUX and/or TV PROG so that "F-1" appears in place of a preset position number. 6 9 4 SET EDIT MODE See "Picture Control" on page 20. TV PROG 1 ? START CAMCORDER Engage its Play mode. 3 START RECORDER Engage its Record mode. NOTES: All necessary cables can be obtained from your dealer. When you select EDIT to dub tapes in step 3, be sure to select AUTO (or NORM when B. E. S. T. is set to OFF) after you finish dubbing the tapes. Recorder DISPLAY STANDBY/ON TIMER VIDEO(MONO)L ­AUDIO­ R REC LINK TV PROG VIDEO input AUDIO input VIDEO OUT Audio/Video Cable (not provided) Camcorder AUDIO OUT Player 26 ADVANCED OPERATIONS (cont. ) On-Screen Display You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. Other Functions Turn on the TV and select the VIDEO channel (or AV mode). 1 2 ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Move the highlight bar (pointer) to "MODE SET" by pressing %fi, then press OK or #. 1 4 7 2 5 8 0 3 2 6 9 4 3 OK ENABLE/DISABLE ON-SCREEN DISPLAY The default setting is "ON", so if you want onscreen displays, leave the setting as it is and go to step 4. [. . . ] 7 0 VCR Indicator lights when the video recorder is in the video mode. "Cassette Loaded" Mark lights once a cassette is inserted; remains lit until cassette ejected. displayed, shows time remaining from With current tape position to end of tape ( pg. Counter, Preset Position*, Clock and Tape Remaining Time Display appear alternately when DISPLAY (or ­ ­:­ ­) is pressed. * Preset Position is not displayed during playback. # Mode shows external input mode selected (L-1, L-2 or F-1). 46 REMOTE CONTROL 1 2 3 4 5 6 7 8 9 0 ! [. . . ]