User manual JVC HM-HDS4

[. . . ] HDD & S-VHS VIDEO RECORDER HM-HDS4EK INSTRUCTIONS LPT0737-001A EN 2 SAFETY FIRST The STANDBY/ON 1 button does not completely shut off mains power from the unit, but switches operating current on and off. "`" shows electrical power standby and "!" shows ON. Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder. When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear. ) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly. [. . . ] ( * Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers. 52 Remote A/B/C/D Code Switching The remote control is capable of controlling four JVC video recorders independently. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B, C or D code signals. REMOTE CONTROL FUNCTIONS On the remote control Slide TV/CABLE/SAT to the right, then press and hold S-VHS during steps A through B. A Change the remote control code. B Set the remote control code. Press OK to set the code. Press the number key "1" for A, "2" for B, "3" for C or "4" for D. On the recorder C Display the code. ? Press 4 on the recorder for over 5 seconds while the recorder is turned off. The code currently set appears on the front display panel. If the code displayed on the front display panel is different from the code set on the remote control, go to step D. Press 8 on the remote control. The code currently set on the remote control will be applied to the recorder. D Change the recorder's code. 53 TV Multi-Brand Remote Control Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer's TVs can also be controlled. A Set the TV brand code. Before performing the following steps: Turn off the TV using its remote control. Slide TV/CABLE/SAT to the left and keep S-VHS pressed during this step. Press 1 on the recorder's remote control to turn on the TV and try operations ( step B). Once you have set the remote control to operate the TV, you do not have to repeat this step until you replace your remote control's batteries. If the TV does not function with one code, try entering another. B Operate the TV. ? Press the corresponding button: 1, TV/VCR, TV PR +/­, TV AV, TV %+/­ (Volume), (TV Muting), number keys. For some brands of TV, you must press OK after having pressed the number keys. IMPORTANT Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability. BRAND NAME JVC BLAUPUNKT BRANDT FERGUSON FINLUX FUNAI LG/GOLDSTAR GRAETZ GRUNDIG HITACHI ITT LUXOR MITSUBISHI MIVAR NEC NOKIA NORDMENDE PANASONIC PHILIPS SABA SALORA SAMSUNG SELECO SHARP SONY TELEAVIA TELEFUNKEN THOMSON TOSHIBA CODE 01, 23, 24, 25 19 26 27 30 32 18 28 19 10 28 28 03 29 20 31 26 11 02 26 28 02, 12, 33, 34, 35 28 06 07 26 26 26 14 Control Your TV Using Additional Buttons Use the number keys, and the button, & button to select the TV's channel. With televisions under Code 01, 02, 07, 10, 11, 14, 20, 23, 24, 25, 27, 33 or 35, the button corresponds to the 1-digit/2-digit entry switching button (often labelled ­ /­ ­) of your TV's remote control. With televisions under Code 01, 28, 29 or 34, the & button corresponds to the 10 + button of your TV's remote control. NOTE: The way these buttons are used is determined by your TV. Use these buttons as instructed for your TV's remote control. 54 Satellite Receiver Multi-Brand Remote Control Your remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer's satellite receivers can also be controlled. REMOTE CONTROL FUNCTIONS (cont. ) Before performing the following steps: Turn off the satellite receiver using its remote control. Slide TV/CABLE/SAT to the left and keep S-VHS pressed during this step. Enter your satellite receiver's brand code using the number keys, then press OK. Press 1 on the recorder's remote control to turn on the satellite receiver and try operations ( step B). A Set the satellite receiver brand code. Once you have set the remote control to operate the satellite receiver, you do not have to repeat this step until you replace your remote control's batteries. If the satellite receiver does not function with one code, try entering another. B Operate the satellite receiver. ? Press the corresponding button: 1, TV PR +/­, number keys. The number keys may not function with some satellite receivers. BRAND NAME JVC AMSTRAD CANAL SATELLITE CANAL + D-BOX ECHOSTAR (VIA DIGITAL) FINLUX FORCE GALAXIS GRUNDIG HIRSCHMANN HUMAX ITT NOKIA KATHREIN LUXOR MASCOM MASPRO NOKIA PACE PANASONIC PHILIPS RADIX RFT SABA SAGEM SALORA SAMSUNG SIEMENS SKYMASTER TECHNISAT THOMSON TPS TRIAX WISI CODE 73 60, 61, 62, 63, 92 81 81 85 82 68 89 88 64, 65, 102 64, 78, 99 88 68 70, 71, 96 68 93 70 87, 94 65, 67, 74, 86, 92 74, 92 66, 84, 101 78 69 97 83, 90 68 83 64 69, 98 66, 100 97 83 91 64 IMPORTANT Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability. EDITING 55 About editing of programmes Navigation system has six functions for editing of programmes. About Hybrid Navigation In the sections "Playback with HDD Navigation" ( pg. 36), it is briefly and "Playback with VCR Navigation" ( described how to search for the beginning of each recorded programme using the Navigation functions. More detailed explanations are provided in this section using HDD Navigation by way of example. This recorder has a built-in Hybrid Navigation system, which consists of two Navigation systems (HDD Navigation and VCR Navigation). [. . . ] 43, 80 S-VHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70, 80 E EDITING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 F F-1 INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 T Tape Position Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]