User manual JVC GR-DVL9000EG

[. . . ] 10 Recording Mode Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 4 5 5 6 6 Snapshot (For Tape Recording) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Auto Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Iris Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] " indicator 8 blinks or goes out if the Stabiliser The " cannot be used. EN 22 USING MENUS FOR DETAILED ADJUSTMENT SYSTEM " SYSTEM" functions which are set when the Power Switch y is set to " " are also applied when the Power Switch y is set to "PLAY" ( pg. 24). S Y S TEM ­ MELODY B EEP ­ ON T ALLY ­ ON R EMOTE D EMO MODE ­ ON P R I OR I TY ­ LCD CAM RESET PRIORITY [LCD]: When the LCD monitor is fully open, even if the viewfinder is pulled out, the image is displayed only on the LCD monitor; it will not be displayed in the viewfinder. FINDER: When the viewfinder is pulled out, even if the LCD monitor is fully open, the image is displayed only in the viewfinder; it will not be displayed on the LCD monitor. CAM RESET [CANCEL]: Does not reset all settings to the factory-preset. EXECUTE: Resets all settings to the factory-preset. RETURN BEEP OFF: Even though not heard while shooting, shutter sound is recorded on the tape. BEEP: The beep sounds when the power is turned on or off, and at the beginning and end of recording. [MELODY]: Instead of a beep, a melody sounds when any operation is performed. REMOTE OFF: Disables the camcorder from receiving the remote control's beam signals. [ON]: Enables the camcorder to receive the remote control's beam signals. [ON]: Demonstrates certain functions such as Programme AE with special effects, etc. , and can be used to confirm how these functions operate. Demonstration starts in the following cases: · When the Menu Screen is closed after "DEMO MODE" is turned "ON". Make sure you point the remote control at the camcorder's remote sensor 1. · The camcorder cannot detect the sound mode in which the recording was made during fast-forward or rewind. · The "SOUND MODE" setting is available for both 12-bit and 16-bit sound. (In previous models' functions, "12-bit" is called "32 kHz" and "16-bit" is called "48 kHz". ) RETURN BRIGHT , DATE/TIME , TIME CODE Refer to " CAMERA DISPLAY" on page 23, 24. The factory-preset of "DATE/TIME" in the " VIDEO DISPLAY" Menu is "OFF". ON SCREEN OFF: Camcorder's display (except the date, time and time code) is not shown on LCD or connected TV. [LCD]: Camcorder's display is shown only on LCD and not on connected TV (except the date, time and time code). LCD/TV: Camcorder's display is shown on both LCD and connected TV. Display 12 b i t / SOUND1 L 46 ON SCREEN setting: For playback sound, tape speed and tape running. DATE/TIME setting: For date/time. Playback Sound During tape playback, the camcorder detects the sound mode in which the recording was made, and plays the sound back. 24, select "SOUND MODE" or "12BIT MODE" from the Menu Screen and set it to the desired parameter. 25 . Minutes Seconds Frames* 12 : 34 : 24 SOUND MODE [STEREO ]: Sound is output on both "L" and "R" channels in stereo. 12BIT MODE MIX: Original and dubbed sounds are combined and output in stereo on both "L" and "R" channels. [. . . ] LENS CAP Appears for 5 seconds after power is turned on if the lens cap is attached. <CANNOT DUB ON A LP RECORDED TAPE> <CANNOT DUB ON A 16BIT RECORDING> <CHECK TAPE'S ERASE PROTECTION TAB> · Appears if Audio Dubbing is attempted on a tape recorded in the LP mode. · Appears if Audio Dubbing is attempted on a tape recorded in 16-bit audio. DUB (e) j on the remote control is pressed when the erase protection tab is set to "SAVE". [. . . ]