User manual JVC GR-DVF21

[. . . ] ENGLISH CONTENTS SAFETY PRECAUTIONS PROVIDED ACCESSORIES GETTING STARTED 2­5 5 6 ­ 11 DIGITAL VIDEO CAMERA GR-DVF21 GR-DVF11 Please visit our CyberCam Homepage on the World Wide Web and answer our Consumer Survey (in English only): http://www. jvc-victor. co. jp/english/index-e. html Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 RECORDING 12 ­ 28 Basic Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PLAYBACK 29 ­ 35 29 30 32 34 Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced Connections . . . . . . . . . . . . . . . . . . . . . . . TAPE DUBBING 36 ­ 37 Tape Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] slide the Power Zoom Lever (VOL. ) towards "+" to turn up the volume, or towards "­" to turn down the volume. Rewind Button Fast-Forward Button Play/Pause Button Stop Button Still Playback: Pauses during playback. If still playback continues for more than about 3 minutes, the camcorder's Stop mode is automatically engaged. After 5 minutes in the Stop mode, the camcorder's power is automatically turned off. When 4/6 is pressed, the image may not pause immediately while the camcorder stabilizes the still image. During this time, if PAUSE (6) on the remote control is pressed, Slow-Motion Playback will start. Slow-Motion Playback, Frame-By-Frame Playback, Playback Zoom and Playback Special Effects Available only with the RM-V711U remote control ( pg. 40, 41). NOTES: If Stop mode continues for 5 minutes when power is supplied from a battery, the camcorder shuts off automatically. To turn on again, set the Power Switch to "OFF", then to " ". The playback picture can be viewed in the LCD monitor, viewfinder or on a connected TV ( pg. You can also view the playback picture on the LCD monitor with it flipped over and retracted. LCD monitor/viewfinder indications: ·When power is supplied from a battery: the " " battery pack remaining power indicator is displayed. When power is supplied through the DC cord: " " does not appear. Only a blue screen is displayed. PLAYBACK 30 EN MENU/BRIGHT Dial PLAYBACK Advanced Features Playback Menu The Playback Menu allows you to set the following functions: Playback Sound (32 kHz, 48 kHz), Synchro Comp, Indication, Display and Time Code. 46, 47). Power Switch Display 4 48kHz MODE 32kHz MODE SYNCHRO INDICATION DISPLAY TIME CODE END 1 2 3 4 5 FULL SOUND SOUND1 SOUND2 FULL SOUND SOUND1 SOUND2 ON OFF ON OFF ON OFF Set the Power Switch to " ". Press MENU/BRIGHT. Move the highlight bar to the desired function by rotating MENU/BRIGHT. Then press MENU/BRIGHT, and the highlight bar automatically moves to "END". The menu disappears. Playback Menu FULL SOUND SOUND1 0. 0 ON ON OFF 48kHz MODE 32kHz MODE SYNCHRO INDICATION DISPLAY TIME CODE 4 END FULL SOUND SOUND1 0. 0 ON ON OFF EN31 Playback Sound During playback, the camcorder detects the sound mode in which the recording was made, and plays the sound back. (32 kHz is preset to "SOUND 1" and 48 kHz is preset to "FULL SOUND". ) Recording sound Display FULL SOUND 32 kHz SOUND 1 SOUND 2 FULL SOUND 48 kHz SOUND 1 SOUND 2 Stereo sound "L" sound is output on both channels "R" sound is output on both channels Stereo sound Output sound If you want to change the output sound of a tape recorded at 32 kHz, access the Playback Menu and, in step 3 on page 30, select "32 kHz MODE" and set it for "FULL SOUND", "SOUND 1" or "SOUND 2". NOTES: You can also use the RM-V711U remote control's AUDIO MONITOR button to change the output sound (without having to access the Playback Menu). Make sure you point the remote control at the camcorder's remote sensor. The camcorder cannot detect the sound mode in which the recording was made during fast-forward or rewind. During playback the sound mode is displayed in the upper left corner. INDICATION You can make the playback sound, time code and date indications disappear. [. . . ] Remaining power level: high Remaining power level: exhausted As the battery power comes close to nil, the battery indicator blinks. Appears when no tape is loaded, or when the erase protection tab is set to "SAVE". When this indication is displayed, the camcorder turns off automatically. TAPE!REFER MANUAL E01 -- E06 Appears for 10 seconds after power is turned on if there is no tape loaded. [. . . ]