User manual JVC GR-AX46

[. . . ] COMPACT VHS CAMCORDER GR-AX76 GR-AX46 GR-AX26 Compact VHS (The camcorder illustrations appearing in these instructions are of the GR-AX76. ) For Customer Use: Enter below the Serial Nos. of the GR-AX76U/GR-AX46U/GR-AX26U camcorder and the AA-V11U AC Power Adapter/Charger. The serial numbers are located on the bottom of the GR-AX76U/GR-AX46U/ GR-AX26U, and the AA-V11U. GR-AX76U/GR-AX46U/GR-AX26U AA-V11U Serial No. INSTRUCTIONS LYT0002-015A 2 Dear Customer, Thank you for purchasing the JVC Compact VHS camcorder. [. . . ] press NEAR to access the selection menu for each function (SET CHARACTER ­ pg. SET CHARACTER DATE/TIME END :MENU KEY S. LX OFF OFF OFF 07 GAIN UP TELE MACRO INTERVAL TIMER REC TIME JLIP ID NO. SET CHARACTER DATE/TIME END :MENU KEY NORM ON 1MIN 1/2S 07 5 CLOSE MENU Press MENU. The normal screen reappears. NOTE: The menu is available only in the Record-Standby mode. PAUSE If GAIN UP or TELE MACRO in the Menu has been changed from the factory settings, this mark appears in the viewfinder. 27 MENU GAIN UP S. LX To record a subject in a dark lit environment. When it is more convenient to shoot the subject with a brighter image even if the picture becomes slightly coarse. Automatically selected when the PROGRAM AE select dial is set to AUTO LOCK mode. When it is more convenient to shoot with a less coarse picture although the subject becomes slightly dark. This setting is suitable for measuring sensitivity conforming to EIA-639 (EIA* Standard for Low Light Sensitivity Measurement) *EIA : Electronic Industries Association Allows you to shoot dark scenes with no picture brightness adjustment. Usually the distance to a subject where the lens is in focus depends on the zoom magnification. Unless there is a distance more than 1m to the subject, the lens is out of focus at the maximum telephoto setting. When set to "ON", you can shoot a subject as large as possible at a distance of approx. ·Depending on the zoom position, the lens may go out of focus. NORM OFF TELE MACRO OFF ON INTERVAL TIMER REC TIME JLIP ID NO. OFF This feature allows you to set the parameters for Self-Timer 15 S ( pg. 30 S 1 MIN 5 MIN OFF This feature allows you to set the parameters for Animation and Time-Lapse recording ( 1/4 S pg. 1/2 S 1S This number is necessary when connecting the camcorder to a device such as a computer using the J terminal (JLIP). Allows you to set the current date and time ( SET CHARACTER DATE/TIME = Factory setting and when the PROGRAM AE Select Dial is set to AUTO LOCK NOTE: During shooting in low light, Auto Focus accuracy may decrease even when Gain Up is used. 21). 28 Interval Timer Indicator Rec Time Indicator 1MIN 1/2S RECORDING Advanced Features (cont. ) Self-Timer You can set the delay between pressing RECORDING START/STOP and the actual start of recording. If you secure the camcorder, you (or whomever is operating the camcorder) can enter the scene before recording starts. NOTE: + MENU NEAR Make sure the camcorder is in the Record-Standby mode before performing the following steps. 1 2 ACCESS MENU SCREEN Turn the PROGRAM AE select dial to any position except AUTO LOCK, then press MENU. SET INTERVAL TIME Press ­ or + to move the highlight bar down to "INTERVAL TIMER", then press FAR or NEAR to cycle through the choices. Choose from "15S", "30S", "1MIN", "5MIN", or select to turn the function "OFF". FAR ­ 3 Tally lamp CLOSE MENU Press MENU. 4 S. LX OFF OFF OFF 07 START DELAYED RECORDING Press RECORDING START/STOP. The tally lamp begins blinking, and the blinking frequency increases about 5 seconds before recording is to start. Once recording begins, the lamp stops blinking but stays lit. GAIN UP TELE MACRO INTERVAL TIMER REC TIME JLIP ID NO. while the tally lamp is blinking, press RECORDING START/STOP to stop the blinking, then set "INTERVAL TIMER" to "OFF". 1S 1/2S 1/4S OFF 5MIN 1MIN 30S 15S OFF 29 Animation Give stationary scenes or objects an illusion of movement. This function allows you to shoot a series of pictures, each slightly different, of the same object for a brief period of time. Time-Lapse You can record sequentially at preset time spans. [. . . ] ("The Warranty Period") 1 YR LABOR 90 DAYS THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO. WHAT WE WILL DO: If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. [. . . ]