User manual JVC FS-SD5R

[. . . ] COMPACT COMPONENT SYSTEM FS-SD5R/FS-SD7R/FS-SD9R REMOTE CONTROL DIMMER SLEEP DISPLAY AUTO PRESET FM MODE PROGRAM RANDOM DOOR SLIDE REPEAT AHB PRO CD BASS TREBLE CANCEL PTY/EON DISPLAY MODE UP SET DOWN FADE MUTING MD/AUX CD FM / AM VOLUME FS-SD5R REMOTE CONTROL DIMMER SLEEP DISPLAY AUTO PRESET FM MODE PROGRAM RANDOM DOOR SLIDE REPEAT AHB PRO CD BASS TREBLE CANCEL PTY/EON DISPLAY MODE UP SET DOWN FADE MUTING MD/AUX CD FM / AM VOLUME FS-SD7R, FS-SD9R INSTRUCTIONS For Customer Use: Enter below the Model No. Serial No. LVT0418-002A [B/UB] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Slide the Top Cover backward to allow Unit's top button operation. Slide it toward you to cover the buttons. Tone Control (BASS/TREBLE) You can control the tone by changing the bass and treble. BASS Control You can adjust the bass level (low frequency range level) between 6 and +6. (0: Flat) 1 2 Press the BASS button on the Remote Control. Press the UP or DOWN button on the Remote Control to adjust the bass level. DOWN BASS UP TREBLE Control You can adjust the treble level (high frequency range level) between 6 and +6. (0: Flat) 1 2 Press the TREBLE button on the Remote Control. Press the UP or DOWN button on the Remote Control to adjust the treble level. DOWN TREBLE UP 10 Using the Tuner REMOTE CONTROL DIMMER SLEEP DISPLAY AUTO PRESET AUTO PRESET FM MODE FM MODE MD/AUX FM/AM PRESET TUNING AHB PRO DOWN MULTI CONTROL PROGRAM RANDOM DOOR SLIDE REPEAT CD UP CLOCK TIMER VOLUME AHB PRO CD BASS TREBLE CANCEL PTY/EON DISPLAY MODE PTY/EON < SET 4 FADE MUTING UP SET DOWN UP DISPLAY MODE > DOWN FM/AM PRESET 4 TUNING Band display, Frequency display, Preset channel MD/AUX CD FM / AM FM/AM FM mode indicators STEREO MONO VOLUME RDS indicator * When the System is in use, the display shows other items as well. For simplicity, we show here only the items described in this section. Stations can be tuned in manually, automatically, or from preset memory storage. s Before listening to the radio: Make sure that both the FM and AM (MW/LW) antennas are correctly connected. q Auto Tuning If you press and hold the 4 or button on the Unit or the Remote Control for one second or more, the frequency changes down, or up, automatically until a station is found. OR q Preset Tuning using the Remote Control (Possible only after presetting stations) Select the desired preset number using the UP, DOWN, > and < button on the Remote Control. After 1 second the display will show the preset number's band and frequency. One Touch Radio Just press the FM/AM button to turn on the System and start playing the station you were last tuned to. s You can switch from any other sound source to the radio by pressing the FM/AM button. Tuning In a Station Example: Press the UP button until the preset number 12 "P12" appears. UP DOWN 1 Press the FM/AM button. The Band and Frequency you were last tuned to appear on the display. (If the last station was selected using the preset number, the preset number appears first. ) Each time you press the button, the band alternates between FM and AM (MW/LW). FM/AM or (After 1 second) q Preset Tuning using the Unit Press the PRESET TUNING button to select the desired preset number. Its band and frequency are displayed. FM / AM AM FM AM FM (on the Remote Control) (on the Unit) In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best reception. 2 Select a station using one of the following methods. q Manual Tuning Press the 4 or button on the Unit or the Remote Control repeatedly to move from frequency to frequency until you find the station you want. OR 11 Using the Tuner Presetting Stations You can preset up to 30 FM stations and up to 15 AM (MW/ LW) stations using the Remote Control. Auto Presetting In each band, you can automatically preset FM-30, AM-15 (MW/LW) stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency. AUTO PRESET FM / AM Preset numbers may have been set to factory test frequencies prior to shipment. You can preset the stations you want into memory by following one of the presetting methods below. (for 2 seconds) Manual Presetting SET FM / AM 1 STORED UP DOWN SET SET Select a band by pressing the FM/AM button. Press the AUTO PRESET button on the Remote Control for more than two seconds. Repeat steps 1-2 for the other band. 2 3 or When changing the Band FM = 30, AM = 15 1 2 3 Select a band by pressing the FM/AM button. Press the 4 or button to tune in a station. When the display returns to the one set in step 2 after 5 seconds, press the SET button again. s If you want to change the preset stations, carry out the Manual Presetting for the desired preset numbers. CAUTION: Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again. 4 Press the UP, DOWN, >, or < button within 5 seconds to select the preset number. UP or DOWN button:Increase or decrease the preset number by 1. Pressing and holding the button will continuously increase or decrease the preset number. Pressing and holding the button will rapidly increase or decrease the preset number. To Change the FM Reception Mode When you are tuned into an FM stereo broadcast, the "STEREO" indicator lights up and you can hear stereo effects. [. . . ] By setting the Sleep Timer, you can fall asleep to music and know that your System will turn off by itself rather than play all night. s You can only set the Sleep Timer when the System is on and a source is playing. 1 2 Play a CD or tune in to the desired station. Press the SLEEP button on the Remote Control. The "SLEEP" indicator lights up. sWhen the clock is not set, "CLOCK" and "ADJUST" appear alternately on the display. Set the clock at first. 3 Set the length of time you want the source to play before shutting off. Each time you press the SLEEP button, it changes the number of minutes shown on the display in this sequence: 10 = 20 = 30 = 60 = 90 = 120 = Cancelled = (back to the beginning) The selected number of minutes for the Sleep Timer will stop blinking five seconds later and the display returns to the original one before setting the Sleep Timer. [. . . ]