User manual JVC DR-MH30SE-DR-MH30 Instruction Manual

[. . . ] DVD & HDD VIDEO RECORDER DR-MH30S/ DR-MH20S CABLE/SAT TV OPEN/ CLOSE DVD TV AV STANDBY ON DVD TV/CBL/SAT VIDEO HDD DVD TV 18 PR CANCEL AUX MEMO/MARK LIVE DUBBING TV EDIT PROGRAMME TOP MENU NAVIGATION ENTER MENU RETURN PREVIOUS NEXT SLOW PLAY/SELECT SLOW REC STOP/ CLEAR PAUSE JUMP REC MODE DISPLAY ON SCREEN HELP HDD DVD VIDEO SAT VPS/PDC SET UP 1 STANDBY/ON AUDIO SUBTITLE ANGLE PROGRESSIVE SCAN PULL - OPEN F1 S-VIDEO VIDEO L(MONO)-AUDIO-R DV DV IN LIVE CHECK INSTRUCTIONS LPT0923-001A EN 2 EN SAFETY FIRST IMPORTANT: 8 Please read the various precautions on page 2 and 3 before installing or operating the unit. 8 It should be noted that it may be unlawful to re-record prerecorded tapes, DVDs, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein. CAUTION: 8 When you are not using the unit for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial. Safety Precautions The rating plate and the safety caution are on the rear of the unit. [. . . ] If the copy limited programme is received during timer-recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed. IMPORTANT: If you have moved to a different area or if a broadcasting station's channel number has been changed, the wrong channel number will be displayed on the SHOWVIEW programme screen in step 7. When this happens, set the correct Guide Program number for that station. 70, "SHOWVIEW System Setup") TM 1 Load a recordable disc if recording to DVD. 3 Press rtw e to select "SHOWVIEW", then press ENTER. When "PROGRAMME FULL DELETE UNWANTED TIMER PROGRAMMES" appears on the TV screen, you need to cancel some of the reserved programmes. 47) 4 Press the number keys to enter the SHOWVIEW number of a programme you wish to record. 13 2 23 PROGRAMME > SHOWVIEW (1/2) SHOWVIEW NO. Satellite Receiver Users To timer-record a satellite broadcast using the SHOWVIEW system: A Perform "Satellite Receiver Control Setting" ( pg. C Leave the satellite receiver's power on. TM 1234 SELECT WITH [ ] THEN PRESS [ENTER] PRESS [PROGRAMME] TO EXIT OR Press rtw e to select the desired number key on the screen, then press ENTER. Repeat to enter all needed numbers. 1 4 7 DELETE RECORD TO 2 5 8 0 3 6 9 DELETE ALL DVD CONFIRM PROGRAMME EXIT ENTER SELECT 5 Press rt to select "RECORD TO", then press ENTER. Press rt to select the desired recording deck, then press ENTER. 6 Press rtw e to select "CONFIRM", then press ENTER. If the number you entered is invalid, "SHOWVIEW NO. If "GUIDE PROGRAMME IS NOT SET SET GUIDE PROGRAM THEN RETRY" appears on the TV screen, set Guide Program Numbers manually. 70) TIMER RECORDING EN 45 Weekly/Daily Recording You can record programmes with one of the following weekly/daily timer settings. For the HDD deck When you select a mode other than ONCE, the space on the hard disk drive is saved for new recordings by overwriting previous recordings. To prevent loss of a needed recording, backup programmes you wish to save by dubbing them to DVD discs before overwriting previous recordings. VPS/PDC Recording Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are services designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video unit and have precedence over the advertised times you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end -- even if the broadcast time of a preset TV programme is changed. NOTES: Make sure to press VPS/PDC# after completing timer programming procedure to activate the VPS/PDC recording function. When you use Manual Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. VPS/PDC recording is also possible when a satellite receiver or a cable system is connected to L-2 IN/DECODER connector on your unit. VPS/PDC recording is also possible via the L-1 IN/OUT connector. ONCE (One Time Recording) In this mode a programme will not be automatically overwritten. WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite) When the set weekly programme is broadcast, the programme recorded last week is automatically deleted and overwritten by the new programme. This week's drama Overwritten Last week's drama MON­SUN (FOR A WEEK)/ MON­SAT (FOR A WEEK)/ MON­FRI (FOR A WEEK) (Daily Recording/Weekly Overwrite) When the set weekly programme is broadcast, the programme recorded on the same day last week is automatically deleted and overwritten by the new programme. This week Last week MON TUE WED THU FRI Overwritten How to check if the station being received transmits a VPS/ PDC signal A Hold down DISPLAY for about 5 seconds. If a VPS/PDC signal is detected from the station, "VPS/PDC" will stop blinking. If no VPS/PDC signal is detected from the station, "VPS/PDC" will blink at a slower rate. [. . . ] 35, 38 Region Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Register Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Relief Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]