User manual JVC DLA-HX2U-DLA-HX2 INSTRUCTION MANUAL

[. . . ] ® ® PROJECTOR INSTRUCTIONS DLA-HX2U/DLA-HX2E PC VIDEO OPERATE W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE VOLUME FOCUS QUICK ALIGN. MENU EXIT ENTER PRESET HIDE For customer Use: Enter below the Serial No. DLA-HX2U Serial No. SAFETY PRECAUTIONS IMPORTANT INFORMATION NOTICE (For USA) Language for Manuals of Products using HID Lamps (that contains mercury) This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: http://www. eiae. org. About burning-in of the D-ILA device Do not allow the same still picture to be projected for a long time or an abnormally bright video picture to be projected. [. . . ] The lens cap may be deformed by heat or this may cause malfunction. Lens Cap 24 Basic Operations If projector set up is not yet complete, please read `Adjustments and Settings Using Menus' on page 32 and perform the necessary settings. Basic Operation Procedures Once the basic settings are done, follow the procedures below: 1. Power On 1 Insert the power cord into the wall outlet · The [STAND BY] indicator lights up when the main power is inputted. Light on STAND BY STAND BY LAMP TEMP OPERATE LAMP TEMP OPERATE PC VIDEO 1-2 2 VOL. EXIT Projector: Indicator 2 Press the [OPERATE] button on the projector (or the [OPERATE] button on the remote control unit) for one second or more · The [OPERATE] indicator lights up and the projected image slowly appears. Light on V-KEYSTONE H-KEYSTONE MENU ENTER OPERATE OPERATE LAMP TEMP STAND BY OPERATE PC VIDEO OPERATE 1-2 2 Projector: Control panel Remote control unit Projector: Indicator Notes · Upon projection, the image may flicker for a few seconds, but this is not a malfunction. It will take more than a minute for the brightness to stabilize. W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE VOLUME FOCUS QUICK ALIGN. MENU EXIT 2. Selecting the image to be projected Press [VIDEO] to select which of the image devices of those connected to the [VIDEO IN] ([VIDEO] or [Y/C]) terminals is output VIDEO VIDEO ENTER PRESET HIDE Projector: Control panel Remote control unit Note · Messages are displayed in the language set by the user in the "Language" menu. ( page 39) However, the input mode ([PC1], [PC2], [PC3], [Y/C], [VIDEO]) and button indications ([FREEZE], [D. ZOOM], [EXIT]) are only displayed in English irrespective of the display language setting. · Each time you press either button, the selected input changes as follows. [VIDEO] [Y/C] [VIDEO] : Image from the input [VIDEO] terminal on the right hand side of projector will be projected. [Y/C] : Image from the input [Y/C] terminal on the right hand side of the projector will be projected. Notes · Sound is formed from sound signals connected to the [AUDIO IN] terminal. · When no image is input to the selected input terminal, the message "No Input" is displayed on the screen. ( page 53) 25 Basic Operations Display using the direct buttons The direct buttons enable direct switching and operation without having to go through the menu. VIDEO When "Line display" ( page 39) is set to "5sec" : After changing an input , the new selection will appear on the screen for about 5 seconds. Input mode can be selected by pressing the [PC] button or the [VIDEO] button. PC 1 PC 2 PC 3 Y/C VIDEO Screen display To select a computer or other devices connected to [PC1], [PC2] or [PC3]: Press [PC] PC PC Projector: Control panel Remote control unit · Upon pressing the button, the input mode changes as follows. Audio-Vol 12 Digital zoom x1. 2 PC1 0 PC2 Vert. keystone [PC1]: Projects image from [PC1] input terminal on the right hand side of the projector. [PC2]: Projects image from [PC2] input terminal on PC3 the right hand side of the projector [PC3]: Projects image from [PC3] input terminal on the right hand side of the projector. Horiz. Keystone PC1 0 When "Line display" ( page 39) is set to "5sec": After changing an input, the new selection will appear on the screen for about 5 seconds. When the [DIGITAL ZOOM], [VOLUME], [V-KEYSTONE] or [H-KEYSTONE] buttons are pressed, the level bar of the function is displayed. Screen display Notes · Sound is formed from sound signals connected to the [AUDIO IN] terminal. · When no image is input to the selected input terminal, the message "No Input" is displayed on the screen. ( page 53) · When the [PC2] input terminal is used, "PC2(BNC)" must be selected from the "Options" item in the main menu. ( page 39) `Tele side' 3. `Wide side' `Near side' 3. Adjusting the Zoom Ring (the screen size) To enlarge the screen size: Turn the zoom ring towards the `Wide side' To reduce the screen size: Turn the zoom ring towards `Tele side' 4. `Far side' 4. Adjusting the Focus Ring (Focus) To focus on nearer points: Turn the focus ring towards the `Near side' To focus on farther points: Turn the focus ring towards the `Far side' 26 Basic Operations 5. Adjusting the Sound Volume To increase the volume : press [VOLUME] ª (0 50) To lower the volume : press [VOLUME] · (50 0) VOL. VOLUME STAND BY LAMP TEMP OPERATE Projector: Control panel Remote control unit When "Menu display" ( page 39) is set to "15sec", after pressing the [VOLUME] button, the sound volume display will appear on the screen for about 15 seconds. (Press [EXIT] button to immediately remove the "Audio-Vol" display. ) PC VIDEO 6-1 VOL. V-KEYSTONE H-KEYSTONE 5 Audio-Vol 12 MENU EXIT ENTER Audio-Vol 12 Screen display Note · When the sound volume is displayed on the screen, pressing the [PRESET] button will reset the set value to "0". OPERATE PC VIDEO 6-1 6. Power Off 1 Press the [OPERATE] button on the projector (or the [OPERATE] button on the remote control unit ) for 1 second or more · The [OPERATE] indicator will disappear, the [STAND BY] indicator starts to blink, and the projector goes into the cooldown mode. The [STAND BY] indicator will continue blinking for approximately 90 seconds as the temperature of the light source lamp cools (Cool Down Mode). W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE VOLUME FOCUS QUICK ALIGN. 5 MENU EXIT ENTER Turn off PRESET HIDE Blink OPERATE OPERATE STAND BY LAMP TEMP OPERATE Projector: Control panel Remote control unit Projector: Indicator Note · The [OPERATE] button will not work for approximately 1 minute from when the light-source lamp is turned on. Wait approximately 1 minute before pressing. 2 Plug out the power cord from wall outlet Caution · Please do not pull out the plug from the power source when the [STAND BY] indicator is blinking. [. . . ] Only 0. 01 % or less of the pixels would either not lit up or remain permanently lit up. *3 The image of [DVI-D] input terminal might not be displayed due to HDCP specification change. · Design and Specifications are subject to change without notice. · Please note that some pictures and illustrations may have been be abridged, enlarged or contextualized in order to aid comprehension. [. . . ]