User manual JVC AX-R551BK

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION To reduce the risk of electrical shocks, fire, etc. : 1. ATTENTION Afin d'éviter tout risque d'électrocution, d'incendie, etc. : 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l'appareil. [. . . ] · If a program on FM band is broadcast in stereo, STEREO indicator lights. 2 Select a station using one of the following three methods. · Manual Tuning Opening the sliding panel, press 4 / ¢ (lower/ higher frequencies) button repeatedly to change the frequencies step by step until you find the desired station. Preset Station You are possibly not allowed to use the feature until the station presetting completes. In some cases, test frequencies have been already memorized for the system since the factory examined the preset station features before shipment. This is not a malfunction. 14 English Listening to FM and AM Broadcasts English Continued Presetting Stations You can preset up to 30 FM and 15 AM stations into memory by following two methods: manual/automatic presettings. If the setting is canceled before you finish, start from step 1 again. To preset stations automatically -- Auto Preset You can automatically preset 30 FM, 15 AM stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up to the higher frequency. On the remote control only: 1 2 Press FM/AM button to select a desired band. Press and hold AUTO PRESET button on the remote control for more than two seconds. The system automatically starts searching for stations with the strong signals continuously, and they are stored successively into memory as follows: To preset stations manually -- Manual Preset 1 Press 4 / ¢ (lower/higher frequencies) button to tune in the desired station manually. 2 Press SET button. "SET" appears in the display window for a while (not blinking). « « « · Note that "SET" message disappears, presetting procedure is cancelled. 3 Rotate MULTI JOG dial or press repeatedly UP/ DOWN button to select the preset channel numbered from 1 to 30 on FM, or 1 to 15 on AM. When you unplug the AC power cord or if a power failure occurs The preset stations will be erased in a few days. If this happens, preset the stations again. To change the FM reception mode · Note that the selected channel "02" disappears, presetting procedure is cancelled. Each time you press the button, the last programed track is erased from the end of program. · To add new tracks to the program before you start playing-back, simply select a track number again you want to add (repeat steps 3 to 4). Track number Program number Here the track number 2 on the CD is stored into a program number 1, and shortly after that the total playback time of programed tracks appears in the display window as follows: To erase all the programed data After playing back the CD, you can erase all the programed track data by pressing 7 (stop) button. New program can be entered again. To exit from the Program play mode Total playback time 5 Repeat steps 3 to 4 to program other tracks you want up to 32 tracks. · If you try to program a 33rd step "MEMORY FULL" will appear in the display window, and your entry is ignored. · The total playback time of programed tracks exceeds 99'59" "­ ­ : ­ ­" will appear in the display window. Before or during playback, you can exit from Program play mode as follows: · Before playback, press PLAY MODE button twice. · During playback, press 7 (stop) button then PLAY MODE button twice. Playback mode indicator goes off and the system resumes Normal play mode. Pressing 0 (open/close) button to open the CD tray also quits and erases the program play. 6 Press 6 (play/pause) button on the CD unit. · When Program play finished, CD unit automatically stops. 7 To check the program contents Before playing back the CD, you can check the program contents by using 4 / ¢ button. Press ¢ button: Shows the programed tracks in the programed order. Press 4 button: Shows them in the reverse order. 18 English Continued English Continued Playing at Random -- Random Play The tracks of the loaded CD will play in no special order (at random) when you select this mode. Repeating Tracks -- Repeat Play You can have the entire disc, the programed tracks, or the individual track repeat as many times as you like. 1 Place a CD. If the current playing source is not the CD, press 6 (play/pause) button on the CD unit, then 7 (stop) button before going to the next step. Press PLAY MODE button repeatedly until "CD RANDOM" appears in the display window. 1 Place a CD. [. . . ] Enclose, with the unit, a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit. Print your home return address on the outside and the inside of the carton. Send to the appropriate JVC Factory Service Center as listed above. Don't service it yourself. Refer servicing to qualified service personnel. ACCESSORIES To purchase accessories for your JVC product, you may contact your local JVC Dealer. [. . . ]