User manual JVC AV-28WFX1

[. . . ] COLOUR TELEVISION AV-32WFX1EU AV-28WFX1EU Instructions Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. ENGLISH WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS UNIT. Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit. Avoid improper installation and never position the unit where good ventilation is unattainable. [. . . ] However, if the Digital VNR effect is increased more than necessary, it has a detrimental effect of reducing the sharpness of the picture. By setting the Digital VNR function to AUTO, the TV will automatically adjust the effect level of the Digital VNR function to match the amount of noise in the picture and give the optimum noise reduction effect for the picture. 3 Press OK . This completes the setting. Note: · The DigiPure setting can be changed using the buttons on the TV's front panel. Pressing the button for 5 seconds or longer causes the current DigiPure setting to be displayed. Change the DigiPure setting while it is being displayed using the - / + buttons. 1 Press / to choose DIGITAL VNR. 2 Press / to choose AUTO. MIN: The effect of the Digital VNR function is kept at the minimum irrespective of the amount of noise in the picture. When viewing an excellent quality picture which contains almost no noise, the picture sharpness may be improved by changing the Digital VNR setting from AUTO to MIN. However, since the noise reduction effect becomes very low, this is not suitable for a picture which contains a lot of noise. MAX: The effect of the Digital VNR function is kept at the maximum irrespective of the amount of noise in the picture. When viewing a picture which contains a lot of noise, the picture noise may be further reduced by changing the Digital VNR setting from AUTO to MAX. However, since using the noise reduction at maximum may have the reverse effect of reducing the sharpness of the picture, MAX is not suitable for an excellent quality picture which contains almost no noise. 3 Press OK . This completes the setting. 16 Picture Features Colour System The colour system is automatically chosen, but if the picture is not clear or no colour appears, choose the colour system manually. 4:3 Auto Aspect You can preset one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Press / to choose COLOUR SYSTEM. Then press OK . . The 4:3 AUTO ASPECT menu appears. ENGLISH 2 Press system. / to choose the appropriate colour PAL: PAL system. Notes: · The AUTO may not function properly with poor signal quality. If the picture is abnormal in AUTO mode, choose another colour system manually. · When in the TV mode (PR 1 to PR 99), you cannot choose AUTO, NTSC 3. 58 or NTSC 4. 43. · When in the TV mode (PR 0), you cannot choose NTSC 3. 58 or NTSC 4. 43. 2 Press / to choose a ZOOM mode. 3 Press OK . This completes the setting. Picture Tilt There are cases where the effects of the magnetic pull from the earth may make the picture tilt . If this happens, correct the picture as follows. 1 Press / to choose PICTURE TILT. Then press OK . The PICTURE TILT menu appears. 3 Press OK . This completes the setting. 2 Press / until the picture becomes horizontal. 3 Press OK . The correction is complete. 17 Sound Setting Sound Adjustment You can adjust the sound to your liking. 1 Press / to choose an item. 2 Press / to adjust it. Item Weaker BASS TREBLE BALANCE Stronger Stronger Right 1 Display MENU. MENU OK Weaker Left 3 Press 2 Choose SOUND SETTING. P OK . This completes the settings. BBE P You can use the BBE function to enjoy easy-to- listen sound that is faithful to the original sound recorded. 3 Display the Sound Setting menu. MENU OK 1 Press / to choose BBE. 2 Press / to choose ON. To cancel the BBE function : Press / to choose OFF. Stereo / I · II You can choose Multi Sound mode for stereo broadcast programmes and bilingual programmes. 3 Press OK . This completes the setting. · Licensed by BBE Sound, Inc. BBE is a registered trademark of BBE Sound, Inc. Note: · Multi Sound has no effect on programmes other than A2 (B/G, D/K) or NICAM (B/G, D/K, L, I) broadcast programmes. Hyper Sound You can enjoy sounds with a wider ambience. 1 Press / to choose STEREO / I · II. 1 Press / Notes: · The Multi Sound mode display is different from the broadcast programme. And the STEREO / I·II does not appear in SOUND SETTING menu. to choose HYPER SOUND. 2 Press / to choose ON. · To cancel the Hyper Sound, choose OFF 3 Press OK . (Hyper Sound) button. This completes the setting. 2 Press / to choose a Multi Sound mode. : Stereo sound : Bilingual I (Sub I) : Bilingual II (Sub II) : Normal sound Using the You can turn on the Hyper Sound with one touch. [. . . ] EXT-1 terminal page 29 page 2 pages 2, 20, 28 @ EXT-2 terminal # EXT-3 terminal pages 2, 5, 20, 28 pages 20, 28 31 Troubleshooting · If the plug is disconnected from the AC socket, or the TV aerial has problems, you may think there is a problem with the TV itself. Be sure to check the following before calling for service. IMPORTANT · Review all instructions in this manual Problem s GENERAL The TV cannot be turned on. · · · · · · · · · · Action Insert the plug in an AC socket. Inoperable remote control. MENU cannot be displayed. s PICTURE Poor colour. [. . . ]