User manual JURA IMPRESSA E25

[. . . ] JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www. jura. com = Note = Important = Tip Fig. Power Switch 17 19 18 Contents JURA IMPRESSA E10/20/25 1. Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1. 1 Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1. 2 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. Preparing the IMPRESSA E10/20/25. . . . . . . . . . . . . . . . . page 2. 1 Check supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. 2 Check electrical fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. 3 Fill water tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. 4 Fill coffee beans. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. 5 Adjusting the grinding gear . . . . . . . . . . . . . . . . . . . . . . . page 2. 6 Power switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3. [. . . ] Do not replace the replaceable hot water jet (14) directly after drawing off water, because the jet is hot after the draw-off operation. At the start of the water draw-off operation there can be splashing Avoid direct contact with the skin!If the required water quantity is reached, close the steam / hot water draw-off tap (12). Do not replace the replaceable steam/hot water jet (13) directly after drawing off steam, because the jet is hot after the draw-off operation. Steam can be used for heating liquids and frothing milk for cappuccino. Make sure that the replaceable steam/frothing jet (13) is pushed upwards when liquids are heated. During frothing some water will escape the system before the actual frothing process. At the start of the steam draw-off operation there can be splashing The steam jet becomes hot. lights up Place a cup under the steam/frothing jet (13) and immerse it in the milk to be frothed or the liquid to be heated. flashes When the steam quantity is reached, close the steam / hot water draw-off tap (12). lights up 13. 1 Attaching the Professional Cappuccino Frother or the Easy Cappuccino Frother to the IMPRESSA E10/20/25 Remove either the replaceable hot water jet (Fig. 5) or the replaceable steam / frothing jet (Fig. Now attach the Professional Cappuccino Frother or the Easy Cappuccino Frother (Fig. Connect the milk tube with the Auto Cappuccino or the Easy Cappuccino. The separate milk container (optional) is ideally suited for drawing in the milk. This is how you connect it to your IMPRESSA E10/20/25 (Fig. 8). 13. 2 Making cappuccino and hot milk with the Professional Cappuccino Frother A little hot water may drip from the jet before you start drawing off milk. Drawing off steam with the Professional Cappuccino Frother or Easy Cappuccino Frother The Professional Cappuccino Frother and the Easy Cappuccino Frother are optional. Please contact your authorized dealer. 12 13. 3 Making cappuccino with the Easy Cappuccino Frother A little hot water may drip from the jet before you start drawing off milk. Switching off the IMPRESSA E10/20/25 To ensure perfect operation, please switch your IMPRESSA E10/20/25 to standby mode with the (6) symbol first. lights up Switch off your IMPRESSA E10/20/25 using the ON/OFF key (6). Programming When your IMPRESSA E10/20/25 leaves the factory it is adjusted such that you can draw off coffee without having to change any settings. You can programme the following stages: ¼ Filter ¼ Hardness ¼ Auto-off 13. 4 Cleaning the Professional Cappuccino Frother and Easy Cappuccino Frother After having frothed milk, the Professional Cappuccino Frother and the Easy Cappuccino Frother need to be cleaned. Place a sufficiently large receptacle under the Professional Cappuccino Frother or the Easy Cappuccino Frother. [. . . ] flashes lights up The de-scaling operation was completed successfully. 18. 1 De-scaling the IMPRESSA E10/20/25 without display (7) request Press the maintenance key (4) until or or appears. Press the maintenance key (4. ) The program «De-scale» is now active. Now proceed as described in Chapter 18 as from lights up, lights up. E 19. Disposal Please return the IMPRESSA E10/20/25 machine to your local dealer, the service shop or to JURA for proper disposal. 17 20. [. . . ]