User manual JUNO JSV7510

[. . . ] This symbol or numbered instructions lead you step by step through the operation of the appliance. Next to this symbol you receive additional information and practical tips on using the appliance. Tips and instructions for the economical and environmentally friendly use of the appliance are marked with a clover leaf. In the event of a malfunction, these operating instructions contain information on how to rectify faults yourself, see the section "In the event of a fault". [. . . ] vinegar concentrate or dishwasher detergent) as this would damage the appliance. Open the lid to the dispenser by pressing the lid catch towards the compartment and lift the lid. Wipe off any spillage carefully to prevent excessive foaming during the next wash programme. Fill with rinse aid: When the indicator light on the control panel is lit. Switching the rinse aid dispenser off If dishwasher detergent with rinse aid is used, you can switch off the rinse aid dispenser and the lamp that indicates that the rinse aid dispenser is empty. Press the combination buttons simultaneously and hold them pressed in. When the first three programme indicator lamps starts to flash, you can let go of the buttons. The lamp for the rinse aid button starts to flash and the lamp for the ended programme cycle is lit. Press the button once more and the lamp for the ended programme cycle goes out. Now the function for the rinse aid dispenser is off and the control lamp is out. To reset the function, follow steps 1 and 2 above and then press the rinse aid button twice, until the lamp for the ended programme cycle is lit again. 12 Instruction book Adjusting rinse aid dosing The dispenser holds about 150 ml. You can set the dosage between 1 - 6, equivalent to 1 - 6 ml rinse aid. The lamp for the buzzer button starts to flash and the lamp for the ended programme cycle is lit. Press the button once more and the lamp for the ended programme cycle goes out. To reset the function, follow steps 1 and 2 above and then press the buzzer button twice, until the lamp for the ended programme cycle is lit again. 18 Instruction book Switching the dishwasher off / unloading Switch the dishwasher off when the buzzer for ended programme sounds (approx. 15 minutes after the end of the programme so that they dry better and cool down. Check the filters to see if they need to be cleaned when the dishwasher has finished the programme. Always let the dishes cool down before unloading. 19 Instruction book Care and cleaning Machine Clean the outside surfaces of the appliance using a mild (non-abrasive) household cleaning product. Do not use cleaning products which contain alcohol (spirits), thinners and similar substances. Spray arm (1) It is important to keep all the holes in the spray arm clear. If the spray arm needs cleaning, unscrew the nut anti-clockwise, remove the washer and lift off the spray arm. Clear the holes and shake out any food remnants. Coarse filter/microfilter (2) The purpose of the coarse filter is to catch large objects such as toothpicks and pieces of eggshell. Lift it out and rinse it under running water whenever necessary. Fine filter (3) It is just as important to keep this filter clean. The fine filter can easily be lifted out for cleaning when you have removed the coarse filter. 20 Instruction book Cleaning the outer door It is possible to remove the outer door from the plastic door in order to clean inside it if necessary. [. . . ] If you would like a wooden door, drill or mill respectively as per the diagram below (your wooden door supplier has the requisite tools), holes for the hinge locking plates (A) diameter 35 mm, predrill the holes for the hinge brackets (B) diameter 2 mm and guide rods (C) diameter 5 mm. 4, 7 kg to get good balance. A B C 29 Position- and connection instructions Preparing the outer door Screw the guide rods and hinges on the door into place using the predrilled holes. 2x Mount plate Before installing the dishwasher and adjusting the door onto the cupboard, put the mount plate into its correct position on the shelf. Mark the holes for screws and the holes for dismounting the outer door. The door can be disconnected if necessary, through hole 1 (two holes). [. . . ]