User manual JUNO JDK4531E

[. . . ] · For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. · Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc. ). [. . . ] · Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. · Place bracket 7. 2. 1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. · Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm above the horizontal reference line. · Fix the lower bracket 7. 2. 1 using the 12a screws (4, 2 x 44, 4) supplied. · Fix the upper bracket 7. 2. 1 and the air outlet connection support 7. 3 together using the 2 screws 12a (4, 2 x 44, 4) supplied. · Insert the two screws 12a (4, 2 x 44, 4) supplied in the hood body fixing holes, leaving a gap of 56 mm between the wall and the head of the screw. GB X 7. 2. 1 13 Mounting the hood body · Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. · Hook the hood body onto the screws 12a · Fully tighten support screws 12a · Adjust screws Vr to level the hood body. Vr 12a Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. · To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. · Fix the pipe in position using sufficient pipe clamps (not supplied). · Remove any activated charcoal filters. ø 150 9 ø 120 RECIRCULATION VERSION AIR OUTLET · Put connection 15 into the connection support 7. 3. · Insert the connection extension pieces laterally 14. 1 in connection 15. · Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. · Connect the air outlet connection 15 to the hood body outlet using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. · Ensure that the activated charcoal filters have been inserted. ELECTRICAL CONNECTION · Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. 14. 1 15 ø 150 GB 14 Flue assembly Upper exhaust flue · Slightly widen the two sides of the upper flue and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. · Make sure that the outlet of the extensions pieces is aligned with the chimney outlets. 2 7. 2. 1 12c 2. 1 Lower exhaust flue · Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. · Fix the lower part laterally to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. 2. 2 12c USE Control panel L S L S V1 V2 V3 Light Led Motor Speed Intensive V1 V2 V3 Switches the lighting system on and off. [. . . ] Cet appareil est conforme à la norme européenne en matière de basse tension C. E. E. 73/23 de sécurité électrique ainsi qu'aux normes européennes : C. E. E. 89/336 en matière de compatibilité électromagnétique et C. E. E. [. . . ]