User manual JUICEMAN JM400 8-2009

[. . . ] Only original spare parts guarantee the safety of the appliance. 4 IMPORTANT SAFETY INSTRUCTIONS ~ The appliance is completely isolated from the electricity supply when: ­ it is turned off at the wall switch and unplugged, or ­ the circuit breaker has been "tripped". ~ Never drape items over the heater plate when it is heated. Hang laundry on the swing out bar. ~ The swing out bar is only to be used to hang laundry. This could tip over the rotary iron. ~ Do not damage, remove or bypass the safety components or control elements of the appliance. ~ Only operate the rotary iron when all removable outer casings are fitted so that it is impossible to touch an electrical component or moving part. [. . . ] Start ironing at a lower temperature and gradually increase the temperature according to the fabric being ironed. ß Woolens, Silk Cottons, Linen ßß ßßß press under a damp cloth slightly damp quite damp 12 Before ironing Testing the finger guard The finger guard is a safety feature and should be checked each time the rotary iron is used. Please note: Any unevenness in the ironing cover will smooth itself out after 3 hours of use. When using a new machine, if delicate laundry is not properly pulled into the rotary iron continue ironing. If a new ironing cover is used, wash the cloth at a high temperature (140°F/ 60°C) to achieve an optimal pull-in of the laundry. ^ If you lift the finger guard now, the roller stops rotating and the heater plate rises. ^ Let go of the finger guard and remove your foot from the foot pedal. The heater plate lowers and the roller rotates. 13 Ironing Turning on and off Selecting the ironing temperature The temperature selector is used to set the ironing temperature. The temperature range is marked by dots on the ring around the temperature selector. These correspond with the international fabric care symbols for ironing. Material Polyester / artificial silk Silk / Wool Cotton / Linen Dot symbol ß ßß Temperature range cool iron (low temperature) medium hot iron (medium temperature) hot iron (high temperature) The rotary iron is turned on and off with the "I / 0" button. The indicator light goes out. ßßß 14 Ironing Selecting the roller speed There are 5 roller speed settings, from low (approximately 6. 5 ft/min. [2 m/min]) to high 15 ft/min. A lower roller speed makes it easier to iron complicated articles such as shirts and blouses. Collar The collar is ironed on both sides using the left hand end of the roller. ^ Iron from the button hem up to the armhole. ^ Iron the button side inside out so the buttons are pressed into the cushioned surface of the roller. ^ Then turn down the collar and press lightly, holding taut. 22 Ironing Tips 4. ^ Starting from the side seam iron past the armhole, then pull the shirt further onto the roller and iron the full back length to the second arm hole. ^ First iron both sides of the cuff on the left edge of the roller. Fold double-cuffs with one button hole placed over the other one and press lightly. ^ Smooth out the sleeve and place it on the edge of the roller. ^ Pull the shirt further down the roller and iron past the arm hole. ^ Iron the arm from the edge of the cuff to the underarm. Shift diagonally to iron the full width of the arm hole. 23 Ironing Tips Pants Ironing pants and jeans ^ Iron the upper part from waistband to inseam of pants and jeans in sections. Pressing woolen and dress pants Skirts These are best ironed without the feed board. ^ Iron each section of the skirt in turn. ^ Lay the pant legs separately on the roller. Then turn the roller by hand until the part of the pants to be pressed is covered by the heater plate. ^ Press each leg from both sides starting from the crease. 24 Cleaning and Care Cleaning the heater plate ^ Check that the temperature selector is set " g " (cold). ^ Clean lime or starch deposits from the heater plate using a non abrasive household cleaner. [. . . ] Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability and longevity of your Miele appliance. Please note that unless expressly approved in writing by the Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. To learn more about MieleCare Extended Service Contracts, please contact your appliance dealer or visit us online at: http://store. miele. com When contacting the Technical Service Department, please quote the Model and Serial number of your appliance, both are shown on the data plate, located underneath the front side of the ironing table. a Model b Serial number c Voltage / frequency d Minimum fuse rating e Total rated load The wiring diagram is located under the right side of the ironing table. 29 Electrical connection Electrical connection 120 V The appliance is supplied with a power cord and NEMA 5-15 P plug ready for connection to an a. c. [. . . ]