User manual JUICEMAN JM300 12-2008

[. . . ] Only with these parts can the manufacturer guarantee the safety of the appliance. from the electricity supply when: ~ This equipment has not been designed for maritime use or for use in mobile installations such as aircraft or recreational vehicles. However, under certain circumstances it may be possible for an installation in these applications. Please contact the nearest Miele Dealer or Miele Technical Service with specific requirements. Use ~ Defective components should be ~ Be aware of loose fitting or hanging clothing when using the rotary iron. [. . . ] Start ironing at a lower temperature and gradually increase the temperature according to the fabric being ironed. Minimum Iron (Perlon, Nylon, etc. ) ß Woolens, Silk Cottons, Linen ßß ßßß ^ Iron starched items last to avoid any starch deposits on other items. press under a damp cloth slightly damp quite damp 13 Before ironing Testing the finger guard The finger guard is a safety feature and should be checked each time the rotary iron is used. Please note: Any unevenness in the ironing cover will smooth itself out after 3 hours of use. When using a new machine, if delicate laundry is not properly pulled into the rotary iron continue ironing. If a new ironing cover is used, wash the cloth at a high temperature (140°F/ 60°C) to achieve an optimal pull-in of the laundry. ^ If you lift the finger guard now, the roller stops rotating and the heater plate rises. ^ Let go of the finger guard and remove your foot from the foot pedal. The heater plate lowers and the roller rotates. 14 Ironing Turning on and off Selecting the ironing temperature The temperature selector is used to set the ironing temperature. The temperature range is marked by dots on the ring around the temperature selector. These correspond with the international fabric care symbols for ironing. Material Minimum Iron Dot Symbol Temperature range cool iron (low temperature) medium hot iron (medium temperature) hot iron (high temperature) 104 - 140 °F (40 - 60 °C) ß ßß ßßß I The rotary iron is turned on and off with the "0-I" button. Laundry bar Ironed laundry can be hung over the swing out bar to avoid creasing. , Take care not to press down on the bar when it is swung out, this could cause the rotary iron to tip over. 18 Ironing Ironing tips ­ To avoid creasing stop the roller, pull the item back slightly and smooth out. ­ If possible, always use the whole length of the roller, otherwise the roller will lose its elasticity. Collar The collar is ironed on both sides using the left hand end of the roller. Stop ironing when the button comes to the heater plate. ^ Lay the button hole front on the left hand end of the roller with the side seam along the edge of the roller. ^ Iron the button side inside out so the buttons are pressed into the cushioned surface of the roller. 23 Ironing Tips 4. ^ Starting from the side seam iron past the armhole, then pull the shirt further onto the roller and iron the full back length to the second arm hole. ^ First iron both sides of the cuff on the left edge of the roller. Fold double-cuffs with one button hole placed over the other one and press lightly. ^ Smooth out the sleeve and place it on the edge of the roller. ^ Pull the shirt further down the roller and iron past the arm hole. ^ Iron the arm from the edge of the cuff to the underarm. Shift diagonally to iron the full width of the arm hole. 24 Ironing Tips Pants Ironing pants and jeans ^ Iron the upper part from waistband to inseam of pants and jeans in sections. Pressing woolen and dress pants Skirts These are best ironed without the feed board. ^ Iron each section of the skirt in turn. ^ Lay the pant legs separately on the roller. Then turn the roller by hand until the part of the pants to be pressed is covered by the heater plate. ^ Press each leg from both sides starting from the crease. 25 Cleaning and Care Turn the iron off and unplug it from the outlet before performing any maintenance work. Washing or replacing the iron cover It is normal for the ironing cover on the roller to become slightly brown with use. [. . . ] Possible fault The emergency release was activated. 30 After sales service In the event of a problem, please contact the Miele Technical Service Department. MieleCare (USA only) MieleCare, our Extended Service Contract program; gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability and longevity of your Miele appliance. Please note that unless expressly approved in writing by the Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. [. . . ]