User manual JUICEMAN HB0001S 12-2009

[. . . ] Extension cords do not guarantee the required safety of the appliance (e. g. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. [. . . ] ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. Compartment I holds a maximum of 2 teaspoons (10 ml), compartment II holds a maximum of 3. 5 tablespoons (50 ml) of detergent. The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. The marks indicate the approximate fill level in ml when the door is open in a horizontal position. 25 Use Turning on ^ Make sure the spray arms can rotate freely. The "Start/Stop" indicator flashes and the indicator of the last program run lights up. Program sequence display After a program has been started the current stage of the program is indicated by the program cycle indicator. Standby DA few minutes after the last key is pressed or at the end of the program the dishwasher will switch into Standby mode to save energy. The display and the indicators are turned off and only the Start/Stop indicator light flashes slowly. If refill salt and/or rinse aid or a fault are present in the display, the dishwasher will not switch to Standby mode. Selecting a program Choose your program according to the type of load and soiling. The "Program guide" describes the programs and use. Starting a program ^ Select the desired program with the "Program" button. The indicators "Start/Stop", "Cleaning" and the last selected program light up. Otherwise important program steps could be interrupted. 26 Use At the end of a program When the program has finished the "End" indicator lights. The program cycle indicators "Cleaning", "Drying" and "End" flash at the same time. See data plate for minimum amperage. The fuse has tripped. The drain pump is running when the door is open. There may be a technical ­ Turn the dishwasher off fault. ­ Contact Miele Technical Service. 30 Frequently asked questions Problems water Intake / Drain Problem The "Intake / Drain" indicator flashes. ­ Clean the water intake filter, see "Cleaning and care". ­ The water pressure at the water connection is lower than 4. 35 psi. ­ Remove any kinks in the drain hose. 31 Frequently asked questions General problems with the dishwasher Problem The indicators and the display is dark. The door and the interior walls are still wet after a program has finished. Possible fault The dishwasher has gone into "Standby" mode to save energy. Solution Press the K button to exit Standby mode. The dispenser was damp Dry the dispenser before when detergent was adding detergent. The moisture will evaporate It is the normal operating after a short time. Before fixing the fault: ­ Press the K button to turn the dishwasher off. [. . . ] This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. , Improper connection of the equipment grounding conductor can result in electric shock. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 47 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , Prior to making a hardwire , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. [. . . ]