User manual JOHN LEWIS JLWM1603

[. . . ] JLWM1603 1600 spin washing machine Instruction manual Automatic Recall Off Cottons Economy Synthetics Delicates Handwash Wool Silk Quickwash Temperature Spin Options Change Exit Start/Pause Memory 1 Memory 2 Delicate spin Spin Drain Rinse JLWM1603 132 987 241 Important Safety Information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. You MUST read them carefully before installing or using the appliance. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. Installation This appliance is heavy. [. . . ] Select the desired temperature Press the "Temperature" button if you wish to select a temperature value different from the one proposed by the washing machine (90°C in this case). The message of the maximum available temperature appears on the second row of the display (instead of "cycle end at"). Depending on the selected programme only certain options are available and shown during the selection phase. Select the "Delay start" Before you start the programme, if you wish the starting to be delayed, choose the "Delay start" option. The selected delay time value (up to 20 hours) will appear on the display while selecting. 13 The end cycle will be updated and shown on the relative position of the display. 13. How to open the door during a programme You can open the door, after having set the washing machine to PAUSE, provided the following conditions exist: · the washing machine is not in the heating phase; · the level of the water is not high; · the drum is not turning. If these requirements are met, when you pause the washing machine, the relevant message appears in the display and the door can be opened. Should it not be possible to open the door, the "Door locked" message appears in the display and the door locked light is on, should it be absolutely necessary to do so, switch the machine off by turning the selector dial on "Off" position. Pay attention to the level and temperature of the water in the washing machine! Delay Start No 10. 55 Delay Start Start in 30 min 10. 55 Temperature Spin Options Change Exit Temperature Spin Options Change Exit 10. The message relevant to the phase that is in progress will be shown in the display. If you have chosen a delayed start, the washing machine will begin the countdown. Start/Pause COTTON Washing 08. 30 12. 00 40°C Temperature 1200 Spin Options Change Exit 14. End of programme At the end of the programme, the washing machine stops automatically, gives an audible signal (if option no sound has not been selected), and displays the relevant message. If you had selected the or option, the "Start/Pause" button light is off and the "Cycle ended/ Door locked" message appears in the display. To drain or spin first turn the programme selector dial to "Off" and then to "Drain" programme or "Spin"/Delicate Spin" programme . Release of the lock is also indicated by the message "Door openable" (cycle ended) being displayed. Turn the programme selector dial to "Off" to switch the machine off. Check whether the drum is completely empty, by rotating it with your hand. The purpose of this is to prevent any items of laundry from remaining accidentally in the drum, where they might get damaged in a subsequent wash (e. g. We advise you to close the water supply tap and disconnect the plug from the socket. How to change an option or a programme during its cycle It is possible to change any option before the programme carries it out. Before you make any change, you must pause the washing machine by pressing the "Start/Pause" button. [. . . ] If the outlet spigot has not been used before, remove any blanking plug that may be in place. P1051 Any necessary adjustment can be made with a spanner. Accurate levelling prevents vibration, noise and displacement of the machine during operation. Some vibration is inevitable, especially if mounted on a wooden floor. If possible, always place the machine on a solid floor. P1197 Special conditions If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. [. . . ]