User manual JOHN LEWIS JLUCLFW6003

[. . . ] Do not damage the refrigerant circuit. Safety precautions for isobutane Warning The refrigerant of the appliance is isobutane (R600a) that is inflammable and explosive to a greater extent. Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. [. . . ] B: When freestanding Cleaning Remove all adhesive tape and packaging, which ensure the accessories do not move in the appliance. Wash the inside of the appliance using lukewarm water and bicarbonate of soda (5ml to 0. 5 litre of water). After cleaning dry the inside of the appliance thoroughly. Location The appliance should be placed in a well ventilated, dry room. The appliance should therefore: not be installed next to radiators, cookers or other sources of heat only be installed at a location where the ambient temperature corresponds to the climate classification, for which the appliance is designed. Levelling The appliance must be level. Level the appliance by adjusting the two adjustable feet (1) at the front of the appliance. If required the washer (2) can be removed. Climate Classification The climate classification can be found on the rating plate located inside the appliance. The following table shows the ambient temperature for each climate classification: Climate Classification SN N ST Ambient Temperature +10 to +32 °C +16 to +32 °C +18 to +38 °C 2 1 7 Door Reversal If required the opening direction of the door can be changed as follows: To reverse the bottom hinge assembly proceed as follows: Disconnect the appliance from the electricity supply. Tilt the appliance backwards, resting the top edge of the appliance on a stool or something similar. Unscrew the adjustable feet situated on both sides (2 pieces), in addition the screws fixing the lower door holders (3 pieces) respectively the screw on the other side. Take off the freezer door by pulling it slightly downwards. Unscrew the top door hinge pin of the refrigerator then screw it back on the other side. Put over the pin in the lower door holding plate in the direction of the arrow. Fix the plate on the other side leaving the position of the door unchanged. Then screw in the one screw in the place set free on the other side as well as the adjustable feet (2 pieces) and set up the box. Put over the handles on the other side and put the plastic covering nails supplied in the plastic bag of this instruction book into the holes set free. Put the appliance to its place, set it level and plug it into the mains socket. 8 Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Should the appliance power supply cable need to be replaced, this must be carried out by a Service Force agent (see page 16). The manufacturer declines any liability should this safety measure not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance's rating plate. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved BS 1363/A fuse must be used. A setting of 3 is usually suitable for normal operation (see thermostat control). Leave the appliance for approximately 4 hours for the correct temperature to be reached before placing food inside. Thermostat Control The thermostat control knob situated inside the refrigerator regulates the temperature of the larder compartment. Thermostat control is marked from 1-5 the higher the number, the colder the setting. Position 0 - Off Position 1 - minimum coldness Position 5 - maximum coldness 10 Using the refrigerator Hints for storage Below is the recommended storage positions for various food types: 1. [. . . ] Under no circumstances should you attempt to repairthe machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. An authorised service engineer always insist on genuine spare parts. 0870 010 7887 They will give you details for your local Service Force Centre. Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working". [. . . ]