User manual JETWAY B 860T

[. . . ] 1 B 860T USER'S MANUAL M/B For Socket 370 Pentium® III Processor NO. B860T Release date: March 2002 Trademark: *Pentium and MMX are trademarks of Intel Corporation. * All the names and brands are the property of their respective owners. *Specifications and Information contained in this documentation are furnished for information use only, are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. 2 TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2-6-2 Headers (1)COM2 Headers (9-pin header) : JC1 This board has another serial port COM2, it comes with the cable providing serial port COM2. (2)USB Port Headers (10-pin header): JU1 These headers are used to connect the additional USB port plug. By attaching an option USB cable, your will get two additional USB plugs affixed to the back panel. (3)Front Panel Headers (2x9-pin header): JP1 1. Power switch: PW-ON This 2-pin connector connects to the case-mounted power switch to power on/ off the system. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without turning off your power switch. Connect the Power LED from the system case to this 2/ 3-pin connector. LAN LED Activity LED: LAN- LED 18 LAN-LED shows the activity of network. Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. See the figure below. (4)FAN Speed Headers (3-pin) : JF1, JF3 These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer. The red wire should be positive, while the black one should be ground. Connect the fan's plug to the board according to the polarity of connector. (5)IR infrared module Headers (10-pin) : JI1 This connector supports the optional wireless transmitting and receiving infrared module. To use the IR function, you must configure the setting through the BIOS setup. 19 (6)CD Audio-In Headers (4-pin) : J10 This header is for the CD-ROM Audio connector. (7)Line-in Headers (4-pin) : J6 This header is for Line-in connector. (8)Audio-In/Out Headers (5-pin) : J7 The Audio-in header is for MIC-in connector. The Audio-out header is for Line-out connector. 20 (9)DOC socket : U13, JD1 DOC 32pin dip socket can support flash disk up to 288MB DOC address can select among three address: D000-D1FFh , D800-D9FFh, DE00- DFFFh. 2-7 Start Up Your Computer 1. Be sure all the switches are off and check if the power supply input voltage is set at the proper position. Usually the in-put voltage is 220V~240V or 110V~120V, depending the country. Connect the power supply cord into the power supply located on the back of your system case according to the user's manual of your system. Other external peripherals (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch which is on the front panel of the case. The LED on the monitor may be lit or switch between orange and green colors after the system is on. If it complies with green standards or if it has the power stand-by feature, the system will run the Power-on test. While the tests are running, the BIOS will alarm beeps or additional message will appear on the screen. 21 If you do not see anything within 30 seconds after you turn on the power. Recheck your jumper settings and connections or call the vender for assistance. 6. During the power-on test, press <Delete> key to enter BIOS setup. [. . . ] When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press <Enter>. You may also press <Esc> to abort the selection without entering password. To disable a password, just press <Enter> when you are prompted to enter the password. [. . . ]