User manual JETWAY 917PDCPR106

[. . . ] 917PDCP/917PDCG 917GDCP/917GDCG USER'S MANUAL M/B For LGA 775 Pentium 4 Processor NO. G03917PDCPR106 Rev:1. 0 Release date: June 2005 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Parallel Port Connector (25-pin female): PARALLEL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. (8) (9) VGA Connector (15-pin D-Sub) Connector: VGA (for 917GDCP/917GDCG only) VGA is the 15-pin D-Subminiature female connector for display monitor Audio Line-In, Lin-Out, MIC, Surrback, Surround, GEN/LEF Connector : J1 This Connector are 6 phone Jack for LINE-OUT, LINE-IN, MIC, Surrback, Surround, GEN/LEF Audio output to speaker Line-out : (GREEN) Audio input to sound chip Line-in : (BLUE) Microphone Connector MIC : (PINK) Audio output to speaker-Rear speaker out Surrback : (ORANGE) Surround : (BLACKNESS) Audio output to speaker-Center/Subwoofer speaker out Audio output to speaker-Side speaker out GEN/LEF: (GRAY) (10) Serial Port COM1/COM2(COM2 only for 917PDCP/917PDCG): COM1/COM2 is the 9-pin D-Subminiature mail connector. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. 22 Line-IN PS/2 Mouse PRINT Line-OUT Surrback LAN PS/2 COM1 VGA/COM2 Keyboard GEN/LFE USB2 USB MIC-IN SURROUND (11) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. FDD Pin 1 Floppy Drive Connector (12) Primary IDE Connector (40-pin block): IDE1 (Support ATA 100) This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. IDE1 Pin 1 · · Two hard disks can be connected to each connector. The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. 23 (13) Serial-ATA Port connector: SATA1/SATA2/SATA3/SATA4 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. SATA4 SATA3 SATA2 SATA1 Serial-ATA Port Connector 2-6-2 Headers (1) Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. AUD-G ND AUD-VC C AUDIO Pin 1 2 10 9 Line-Out, MIC Headers (2) USB Port Headers (9-pin) : USB3, USB4 The header is used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. AUD-MIC AUD-MIC-BIAS AUD-FPO -R UT HP- O N AUD- FPO -L UT +DATA G ND O C -DATA Pin 1 Pin 1 +DATA G ND -DATA USB Port Headers 24 +D ATA G ND -DATA VC C VC C -DATA VC C VC C USB3 +DATA G ND O C USB4 (3) (4) IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. Power LED: PWR-LED The Power LED is light on while the system power is on. Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PWR LED PWRBTN PWRBTN PWRLED (5) (6) (7) VCC5 PWRLED Pin 1 JW FP SPEAK Pin 1 SPKR NC VCC5 Pin 1 GND HDLED System Case Connections (8) FAN Power Headers: SYSFAN1, SYSFAN2 (3-pin), CPUFAN (4-pin) These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. Connect the fan's plug to the board taking into consideration the polarity of connector. C PUFAN O UT 4 RESET 1 CPUFAN SYSFAN1 1 3 SYSFAN2 3 1 FAN Power Headers (9) IR infrared module Headers (5-pin) : IR 25 +12V G ND C PUFAN IN GND RSTSW NC VCC5 HDDLE GND This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 2 Pin 1 G ND IR RX 6 5 NC VCC 5 IRTX 1 10 9 IR IR infrared module Headers (10) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 4 C DIN CD Audio-In Headers (11) SPDIF In/Out Header: JP6 (SPDIF Bracket Optional) JP6 2 Pin 1 SPDIF-Bracket Connector 26 NC SPF -IN1 IF SPD -IN2 IF NC 12V SPDIF UT -O G ND NC G ND 2-7 Starting Up Your Computer 1. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. [. . . ] Click NEXT, install REALTEK Gigabit and Fast Ethernet NIC Driver 3. After driver installation completed, Click Finish 48 4-5 PC-HEALTH install Intel Hardware Doctor Utility 1. Click Next when Install shield wizard Window MENU appears appears, Choose destination location and click Next, when the start copy file windows appear, click next 3. Execute MY GUARD utility, On-time Monitoring your system health NOTE: MAGIC INSTALL will auto detect file path X:\INTEL915\MYGUARD\SETUP. EXE This driver supports WINDOWS 2000/XP 49 4-6 PC-CILLIN Install PC-CILLIN 2005 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL MENU appears 2. Please select "Install program" when the "Trend Micro internet security" installshield wizard windows appears 3. Click NEXT and Enter your Customer Information, Click NEXT or choose Change to change the path for the file to be stored 4. Please select install "FULL" function or install "Antivirus software" only 5. We suggest to use "Recommend configuration". Click Install to install PCCILLIN 2005 internet security software , then select to restart your computer Note : Please install ACROBAT READER for reading PC-CILLIN 2005 User Manual which locates at the path "X:\acrobat\adberdr6_enu_full. exe". 50 4-7 HOW TO UPDATE BIOS Before update BIOS users have to "Disable", "Flash Part Write Protect" item which in "Miscellaneous Control" of BIOS SETUP. [. . . ]