User manual JETWAY 915GDBR3A

[. . . ] 915GDBG/915PDBG USER'S MANUAL M/B For LGA 775 Pentium 4 Processor NO. G03-915GDB Rev:3. 0 Release date: November 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. Pin 1 (3) (4) (5) (6) (7) USB Port connector: USB1 USB Port connector: UL1 (USB) The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN This connector is standard RJ45 connector for Network connector. PS/2 Mouse & PS/2 Keyboard Connector: KB (PS2 KB/MOUSE) The connectors for PS/2 keyboard and PS/2 Mouse. Parallel Port Connector (25-pin female): PARALLEL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. Audio Line-In, Lin-Out, MIC, Surrback, Surround, GEN/LEF Connector : J1 This Connector are 6 phone Jack for LINE-OUT, LINE-IN, MIC, Surrback, Surround, GEN/LEF Audio output to speaker Line-out : (GREEN) Audio input to sound chip Line-in : (BLUE) Microphone Connector MIC : (PINK) Audio output to speaker-Rear speaker out Surrback : (ORANGE) Surround : (BLACKNESS) Audio output to speaker-Center/Subwoofer speaker out Audio output to speaker-Side speaker out GEN/LEF: (GRAY) VGA Connector (15-pin D-Sub) Connector: VGA (for 915GDBG only) VGA is the 15-pin D-Subminiature female connector for display monitor. (8) (9) (10) Serial Port COM1/COM2: COM1/COM2 (COM2 only for 915PDBG) COM1/COM2 is the 9-pin D-Subminiature mail connector. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. 22 Line-IN PS/2 Mouse PRINT Line-OUT Surrback LAN PS/2 COM1 Keyboard VGA GEN/LFE USB2 USB MIC-IN SURROUND (11) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. FDD Pin 1 Floppy Drive Connector (12) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. IDE 1 Pin 1 (13) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. 23 IDE 2 Pin 1 · · Two hard disks can be connected to each connector. The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. (14) Serial-ATA Port connector: SATA1/SATA2/SATA3/SATA4/SATA5/SATA6 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. Pin 1 SATA4 SATA3 SATA2 SATA1 Pin 1 SATA6 SATA5 Serial-ATA Port Connector 2-6-2 Headers (1) Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. AUD-G ND AUD-VC C AUDIO Pin 1 2 10 9 Line-Out, MIC Headers 24 AUD-MIC AUD-MIC-BIAS AUD-FPO -R UT HP- O N AUD- FPO -L UT (2) USB Port Headers (9-pin) : USB3, USB4 The header is used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. +DATA G ND O C -DATA Pin 1 Pin 1 +DATA G ND -DATA USB Port Headers (3) 1394 Port Headers (9-pin): 1394A, 1394B TPAGND TPBVCC GND +D ATA G ND -DATA VC C VC C -DATA VC C VC C USB3 +DATA G ND O C USB4 1394A Pin 1 Pin 1 TPAGND TPBVCC GND 1394B GND TPB+ VCC 1394 Port Headers (4) (5) Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. Power LED: PWR-LED The Power LED is light on while the system power is on. IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. (6) (7) Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. (8) Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. 25 GND TPB+ VCC TPA+ TPA+ PWR LED PWRBTN PWRLED VCC5 PWRLED Pin 1 Pin 1 SPEAK JW FP Pin 1 SPKR NC VCC5 GND HDLED System Case Connections (9) Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. [. . . ] We call this auto detect software MAGIC INSTALL. MAGIC INSTALL Supports WINDOWS 2000/XP Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or click START / click RUN / type X:\SETUP. EXE (assuming X is your CD-ROM drive). The intel915 serial chipset driver only support Windows 2000 and Windows XP OS From MAGIC INSTALL MENU you may make 11 selections: 1. EXIT to exit from MAGIC INSTALL menu 4-1 INF install Intel 915 chipset system driver 45 1. Select if you want computer re-started click readme information appear, click Next Finish 4-2 VGA install Intel 915G VGA Driver 1. [. . . ]