User manual JETWAY 830CN

[. . . ] 830CN/830CH/830CF USER'S MANUAL M/B For Socket-A Athlon/Duron Processor NO. G03-830CNR5A Release date: November 2001 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are to change at any time without notice, and should not be construed as a commitment by manufacturer. subject TABLE OF CONTENT USER'S NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If it complies with green standards or if it is has a power standby feature. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen. If you do not see any thing within 30 seconds from the time you turn on the power. Recheck your jumper settings and connections or call your retailer for assistance. Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM install or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency 6. Power off your computer: You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. If you use Windows 9X, click "Start" button, click "Shut down" and then click "Shut down the computer?" The power supply should turn off after windows shut down. 23 Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best. In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: · · · · Press <Esc> to quit the BIOS Setup. Press (up, down, left, right) to choose, in the main menu, the option you want to confirm or to modify. Press <F10> when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu. Press Page Up/Page Down or +/­ keys when you want to modify the BIOS parameters for the active option. 3-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup 3-2 Getting Help 24 Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>. 3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. [. . . ] EXIT Install AGPVXD file when use External AGP card (for 830CH/CF) Install SiS 630/730 On-chip VGA driver Install On-chip AC'97 Audio driver Install PCI Fast Ethernet driver (for 830CF) Install Winbond Hardware Doctor Monitoring Software install BIOS Live Update Utility Install PC-CILLIN2000 Anti-virus program Install Sound Application software Install LAN State Utility To browse the contents of the CD To exit from Magic Install menu 4-1 AGPVXD Install SiS 630/730 AGPVXD Driver The AGPVXD Driver Is Only For AGP Slot VGA CARD User, On Board VGA User No 42 Require. (Only for 830CH/830CF) The path of the file: for WINDOWS 9X is X:\SIS630\AGPVXD\WIN9X\SETUP. EXE (including WIN95/98/98SE/ME) for WINDOWS 2000 is X:\SIS630\AGPVXD\WIN2000\SETUP. EXE For WINDOWS 95/98/98SE/ME/2000 1. Click NEXT or choose BROWSE to change the path For the file to be stored 4. After Setup complete please select restart my computer now and click Finish to complete setup 4-2 VGA The path of the file: Install SiS 630/730 VGA Driver 43 for WINDOWS 9X is X:\SIS630\VGA\WIN9X\SETUP. EXE (including Windows 98/98SE/ME) for WINDOWS NT4. 0 is X:\SIS630\VGA\WINNT40 for WINDOWS 2000 is X:\SIS630\VGA\WIN2000\SETUP. EXE for LINUX is X:\SIS630\LINUX A. [. . . ]