User manual JETWAY 615TCFR3A

[. . . ] 615TCF/615TCS USER'S MANUAL M/B For Socket 370 Pentium III Processor NO. G03-615CFR3A Release date: May 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 THERMAL SOLUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press <F10> when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu. Press Page Up/Page Down or +/­ keys when you want to modify the BIOS parameters for the active option. 3-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup 24 3-2 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>. 3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. CMOS Setup Utility ­ Copyright(C) 1984-2000 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Esc : Quit F10 : Save & Exit Setup Time, Date, Hard Disk Type. . . Figure 3-1 Miscellaneous Control Load optimized Defaults Load Standard Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ¡ü ý ú ¡û : Select Item Standard CMOS Features Use this Menu for basic system configurations. Advanced BIOS Features Use this menu to set the Advanced Features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system's performance. 25 Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management Setup Use this menu to specify your settings for power management. PnP/PCI configurations This entry appears if your system supports PnP/PCI. Miscellaneous Control Use this menu to specify your settings for Miscellaneous Control. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Exit Without Saving Abandon all CMOS value changes and exit setup. 26 3-4 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categories. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. CMOS Setup Utility ­ Copyright(C) 1984-2000 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) IDE IDE IDE IDE Primary Master Primary Slave Secondary Master Secondary Slave 1. 4M, 3. 25 in. None EGA/VGA All Errors 640K 64512K 65536K F1:General Help Wed, Jul, 12 2000 16 : 18 : 49 Item Help Menu Level > Change the day, moth, Year and century Drive A Drive B Video Halt On Base Memory Extended Memory Total Memory ¡ü ý ú û Move Enter:Select Item +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Date The date format is <day><month><date><year>. Year Time The time format is <hour><minute><second>. [. . . ] EXIT to exit from MAGIC INSTALL menu Each selection is illustrated as below: 4-1 INF install INTEL 815 chipset system driver After you have completed the installation of your operation system (WINDOWS 95/98/ 98SE). You will find an UNKNOWN DEVICE in the device manager (START/SETTING/ CONTROL PANEL/SYSTEM/DEVICE MANAGER). Select if you want computer re-started by the driver click NEXT click Finish NOTE: MAGIC INSTALL will auto detect file path X:\INTEL815\INF\INFINST. EXE This driver supports WINDOWS 95/98/98SE/ME/2000 (NT4. 0 do not require) 4-2 IDE install Intel ULTRA ATA Storage driver 44 1. Click NEXT or BROWSE to change the path you want the driver stored 5. [. . . ]