User manual JETWAY 603TCR4A

[. . . ] 603TCF/603TCFL USER'S MANUAL M/B For Socket 370 Pentium III Processor NO. G03-603TCR4A Release date: August 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 THERMAL SOLUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. PS/2 Mouse LAN PRINT GAME/MIDI PORT PS/2 USB COM1 Keyboard VGA MIC LINE-IN LINE-OUT (9) Floppy Drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. 15 IDE1 IDE2 Pin 1 Pin 1 Primary IDE Connector (11) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. IDE1 IDE2 Pin 1 Pin 1 Secondary IDE Connector · · Two hard disks can be connected to each connector. The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. 2-6-2 Headers (1) Internal Keyboard Headers (4-pin header) : JKB JKB Pin 1 Internal Keyboard Headers 16 (2) COM2 Headers (9-pin header) : COM2 This board has another serial port COM2, it come with cable providing serial port COM2. Pin 1 Note: Orient the read marking on the COM2 ribbon cable to pin 1 COM2 (3) USB Port Headers (9-pin header): USB2 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. USB2 VCC -DATA +DATA G ND NC VC C -DATA +DATA G ND NC Pin 1 USB Port Headers (4) (5) (6) (7) (8) IDE Activity LED: HDLED This connector connects to the hard disk activity indicator light on the case. Turbo LED switch: TRBLED Since the motherboard's turbo function is always on. You may wish to connect the Power LED from the system case to this lead. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. Speaker connector: SPEAKER This 4-pin connector connects to the case-mounted speaker. Power LED: PW LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. 17 (9) Power switch: PWRIN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. Speaker R eset SW Turbo LE D VCC NC G ND G ND G ND NC VC C G ND VCC Keyboard Lock Power LE D Turbo SW/ SMI G ND G ND IDE LE -D PWR BTN System Case Connections (10) FAN Speed Headers (3-pin) : FAN1, FAN2 These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. Connect the fan's plug to the board taking into consideration the polarity of connector. FAN1 1 3 3 1 FAN2 FAN Speed Headers (11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. Pin 1 Infrared Module Headers 18 IR X R G ND IR TX VC C IR (12) CD Audio-In Headers (4-pin) : CD_IN CD_IN is the connector for CD-Audio Input signal. Please connect it to CDROM CD-Audio output connector. C -IN D 1 4 CD Audio-In Headers (13) Wake On-LAN Headers (3-pin) : WOL1 This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that BIOS Wake-Up by PCI Card is enabled. WOL1 3 1 Wake-On-LAN Headers (14) Line-In/Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-In, Line-out, MIC connector with cable. Pin 1 Line-In/Out, MIC Headers 19 L-O UT-L L-IN-L G ND MIC L-IN-R G ND MICP G ND L-O UT-R AUDIO WO L G ND 5VSB 2-7 Starting Up Your Computer 1. [. . . ] Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. You determine when the password is required within the BIOS Features Setup Menu and its Security option. If the Security option is set to "System", the password will be required both at boot and at entry to Setup. If set to "Setup", prompting only occurs when trying to enter Setup. 34 Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. [. . . ]