User manual JEM ZR33 HI-MASS

[. . . ] Choose a longer lasting fluid (SP) ZR33-DMX USER GUIDE ·User Guide Index · Introduction · Safety · Machine Layout · Getting Started · Using The Remote Control · Using DMX 512 · Using The Slave Socket · The ZR33 Flying Kit · The ZR33 Ducting Kit · Trouble Shooting · How To Contact Us © Martin Manufacturing (UK). 2000 MARTIN MANUFACTURING (UK) PLC Note: Martin Manufacturing (UK) reserves the right to modify or change the specification of this product without prior notice. No part of this publication shall be copied without permission PAGE 1 ZR33-DMX USER GUIDE ZR33-DMX USER GUIDE Introduction The ZR33 features the "HI-MASS" vaporizing system. This consists of a twin coil system, each supplied with fluid from a high pressure oscillating piston pump. [. . . ] This is done by using the JEM ducting adaptor and a length of 100 mm (4") ducting pipe. The length can be anything from a couple of metres up to 20 metres or further. There are one or two things to beware of when using smoke machines with ducting, firstly if there are bends to redirect the smoke they could cause condensation to form also an air space must be provided between the output of the machine and the ducting adaptor. NOTE!Always use the recommended ducting adaptor and ducting pipe, others may cause damage to the machine. PAGE 2 MARTIN MANUFACTURING (UK) PLC MARTIN MANUFACTURING (UK) PLC PAGE 11 ZR33-DMX USER GUIDE ZR33-DMX USER GUIDE ZR33 Flying Kit Safety · Hanging Bracket Safety Strap · · · Always use a JEM approved fluid, other fluids could be dangerous and could cause damage to the machine. Always check the voltage is correct for use with the machine, the voltage setting is printed on the serial label. Always read the user guide before operating the machine, smoke machines need to be operated carefully to avoid risk. Never touch the nozzle at the front of the machine, the nozzle can stay hot for up to 10 hours. Do not remove the cover or attempt to repair a faulty machine, an authorized JEM dealer should be contacted in the event of a faulty machine. Always use smoke machines in well ventilated areas, over use could affect sufferers of asthma or other chest conditions. Do not use the machine if there is a faulty mains lead or plug this could be dangerous. Never point the output directly at peoples heads, this is a high powered smoke machine. Do not spill fluid over the machine, if fluid is spilt clean with clean water and contact an approved JEM dealer for advice. ZR33 HI-MASS · · · The ZR33 flying kit enables the machine to be fixed to rigging and ceilings for use where the ZR33 is best situated in a flying position. The kit is supplied as standard with the option of a drip pad for catching unwanted drips that can occur when smoke machines are angled down. · · · NOTE!A safety strap must be fixed from the rigging to the handle to ensure maximum safety. . Mains Lead Wiring Instructions Brown = Live Blue = Neutral Green/Yelllow = Earth Note!This Appliance must be earthed PAGE 10 MARTIN MANUFACTURING (UK) PLC MARTIN MANUFACTURING (UK) PLC PAGE 3 ZR33-DMX USER GUIDE ZR33-DMX USER GUIDE Machine Layout Fluid container Using The Slave Socket The ZR33 has the ability to connect machines together using a XLR lead and then operating all of the machines with one controller. This is ideal when there is a need for lots of smoke and there is no DMX to operate the machines. Simply remove the controllers from all but one of the machines and then connect an XLR lead (3 pin) from the slave socket of the first machine (the one with the controller) to the next machine's remote socket, and then from that machine's slave to the next machine's remote socket. All of the machines will operate with the same output and timer settings as the first machine. WARNING HIGH TEMPERATURE VAPOUR AND SURFACES Wiring of XLR Output nozzle Pin 1 - GND Pin 2 - NA Pin 3 - 0 -10V signal Remote control First machine Remote socket Slave socket MULTI-FUNCTION CONTROLLER FOG ON 4 3 2 1 OUTPUT 9 5 6 7 8 2 High Performance Fog Generator STAND-BY TIMER ZR33 sefsgsfhdthehd dggdg redrhryj thrhrh rhtrthrth rthrthrhhw rhrtrt rhrtjrjr rjhrj rjtr rjrjryjr;'l'oherw torhrth;hj;d ;o oekh;r ;kh;do okldh;d ;ld rep epe'kdh;dh;dj; oi;osuvistli v; ulgiss;svsuito;svn; ithisvns;i osi norit;si;soiv;svns;o s[os' `spov'peo'`ov sneorvn'svns' psivpso ev e e repeo eporpeop ete ei oeov eoiov ereretete eteteer yeh egprogp p irphgido I [eigpe [i[p eooeihoe eih[ehi[p eihoeih[hoi[e High Performance Fog Generator MULTI-FUNCTION CONTROLLER FOG STAND-BY TIMER ZR33 sefsgsfhdthehd dggdg redrhryj thrhrh rhtrthrth rthrthrhhw rhrtrt rhrtjrjr rjhrj rjtr rjrjryjr;'l'oherw torhrth;hj;d ;o oekh;r ;kh;do okldh;d ;ld rep epe'kdh;dh;dj; oi;osuvistli v; ulgiss;svsuito;svn; ithisvns;i osi norit;si;soiv;svns;o s[os' `spov'peo'`ov sneorvn'svns' psivpso ev e e repeo eporpeop ete ei oeov eoiov ereretete eteteer yeh egprogp p irphgido I [eigpe [i[p eooeihoe eih[ehi[p eihoeih[hoi[e High Performance Fog Generator ZR33 sefsgsfhdthehd dggdg redrhryj thrhrh rhtrthrth rthrthrhhw rhrtrt rhrtjrjr rjhrj rjtr rjrjryjr;'l'oherw torhrth;hj;d ;o oekh;r ;kh;do okldh;d ;ld rep epe'kdh;dh;dj; oi;osuvistli v; ulgiss;svsuito;svn; ithisvns;i osi norit;si;soiv;svns;o s[os' `spov'peo'`ov sneorvn'svns' psivpso ev e e repeo eporpeop ete ei oeov eoiov ereretete eteteer yeh egprogp p irphgido I [eigpe [i[p eooeihoe eih[ehi[p eihoeih[hoi[e ON x8 ON 4 3 5 6 7 8 9 CYCLE 3 2 1 4 5 6 7 8 9 ON ON x8 ON POWER 1 DELAY RUN 4 3 2 1 5 6 7 8 9 3 2 POWER 1 4 5 6 7 8 9 CYCLE 3 2 1 4 5 6 7 8 9 Main fuse A Martin Professional product OUTPUT DELAY RUN A Martin Professional product ON A Martin Professional product 1 2 3 4 5 6 7 8 9 10 PUSH ON ON 1 2 3 4 5 6 7 8 9 10 PUSH 1 2 3 4 5 6 7 8 9 10 PUSH DMX XLR (out) Mains lead Ready LED Mains switch DMX XLR (in) DMX address switches Slave socket To next machine PAGE 4 MARTIN MANUFACTURING (UK) PLC MARTIN MANUFACTURING (UK) PLC PAGE 9 ZR33-DMX USER GUIDE ZR33-DMX USER GUIDE Using DMX 512 Within the lighting industry, the DMX communication protocol is widely used for remote control of lighting and other equipment. The ZR33 is fitted with a DMX 512 compliant interface as standard, giving the user the possibility of controlling the smoke and light from a single source. The ZR33 uses a single channel to fire and control the output level; the interface can be addressed from channel 1 to channel 512. [. . . ] Check the "output" knob is turned fully clockwise (maximum) then press and hold the red "fog" button. The fluid pumps will start operating; if the machine has a new container of fluid it will take a few seconds for the pumps to prime. The output can now be set to the desired level by turning the "output" knob. The timer may be activated or you can simply use the "fog" button when smoke is required, Alternately you may wish to use DMX to operate the ZR33. [. . . ]