User manual JBSYSTEMS SUPER SOLAR RGBW V1.0

[. . . ] Check that the available voltage is not higher than the one stated on the rear panel of the unit. The power cord should always be in perfect condition: switch the unit immediately off when the power cord is squashed or damaged. This fixture must be earthed to in order comply with safety regulations. Always use an appropriate and certified safety cable when installing the unit. [. . . ] To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit. This product meets the requirements of the current European and national guidelines. This device has been designed to produce decorative effect lighting and is used in light show systems. Before you start using this unit, please check if there's no transportation damage. Should there be any, do not use the device and consult your dealer first. Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. Hanging bracket with 2 knobs · Important: Never look directly into the light source!Don't use the effect in the presence of persons suffering from epilepsy. In case of replacement of the lamp or maintenance, do not open the fixture within 10 minutes until the unit cools down after switching off. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. The gobo/color wheel is static and can be controlled with the FUNCTION-button. FUNCTION BUTTON: (strobe/next) Push the FUNCTION button while the Winner is in FAST mode (MODE led is off) the units will strobe in 3 different ways: · Two-light strobe in white color Every time you push the FUNCTION-button while the Winner is in SLOW mode (MODE led is on) the colors/gobos of the connected units change. Controlled by universal DMX-controller: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to "daisy chain" your DMX controller and all the connected light effects with a good quality XLR M/F balanced cable (ex. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Standalone 1unit: Just connect the unit to the mains and put on some music. Two or more units in master/slave setup: Connect 2 or more units together using good quality balanced XLR microphone cables (like for example JB Systems code 7-0063). The unit that has no cable connected to its input will react as master; the others are the slave units. You don't have to worry about the settings of the DMX DIP-switches! [. . . ] How to set the DIP-switches to obtain the right starting address: On the back of the Winner you will see that each of the first 9 DIP-switches corresponds to certain value: You can combine the values of these switches to become any starting address between 1 and 512: Begin address = 01 switch 1=ON values: 1 Begin address = 05 switch 1+3=ON values: 1+4 = 5 Begin address = 09 switch 1+4=ON values: 1+8 = 9 Begin address = 13 switch 1+3+4=ON values: 1+4+8 = 13 Begin address = 62 switch 2+3+4+5+6=ON values: 2+4+8+16+32 = 62 Clean the internal optics at least every 90 days. Mains Input: Fuse: Sound Control: DMX connections: Lamp: Size: Weight: AC 230V, 50Hz 250V 5A slow blow (20mm glass) Internal microphone 3pin XLR male / female HID-150W 50 x 20 x 15. Every information is subject to change without prior notice Make sure the area below the installation place is free from unwanted persons during servicing. Switch off the unit, unplug the mains cable and wait until the unit has been cooled down. [. . . ]