User manual JBSYSTEMS LED COLOR BANK V 1.2

[. . . ] Several built-in chases create stunning effects, controlled by DMX, internal microphone or by a simple hand controller when used in standalone mode. Before you start using this unit, please check if there's no transportation damage. Should there be any, do not use the device and consult your dealer first. Important: This device left our factory in perfect condition and well packaged. [. . . ] The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance. Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Once the correct address shows on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. WALL MOUNT BRACKET: used to easily fix the unit on a wall, ceiling or other flat surface. REMOTE CONTROL connector: used to connect the CA-8 hand controller DMX input: connect this input to the previous unit in the DMX chain or directly to the DMX-controller. DMX output: connect this input to the next unit in the DMX chain SENSITIVITY: to control the sensitivity of the internal microphone MICROPHONE: used to control the music activated internal programs MAINS CONNECTOR: connect the supplied mains cable here MAINS SWITCH: to switch the LED color bank on/off HANGINGBRACKET: used to fix the on truss using a standard clamp MASTER LED: is lit when the unit is switched as master DMX LED: is lit when the unit receives a DMX-signal DISPLAY: shows the various menus and the selected functions SLAVE LED: is lit when the unit is in slave mode SOUND LED: blinks to the rhythm of the music while the unit is in audio mode MENU BUTTON: used to browse and select the different menu items DOWN BUTTON: to go back in the menu or to decrease the values shown on the display UP BUTTON: to go up in the menu or to increase the values shown on the display ENTER BUTTON: used to confirm your choice Once the mode is selected, press the ENTER button to setup (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. This menu option is not available when the unit is set to slave mode Press the MENU button until is showing on the display. Once the right show blinks on the display, press the ENTER button to save it. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again. [. . . ] You need to "daisy chain" your DMX controller and all the connected units with a good quality balanced cable. In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly. The interior of the device should be cleaned annually using a vacuum cleaner or air-jet. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. [. . . ]