User manual JBSYSTEMS LIGHT MATRIX LED V 1.0

[. . . ] Extremely brilliant colors compared to effects with halogen lamps No lamp replacements!Virtually no heat production and very low power consumption 0-100% dimming and ultra fast strobe function Equipped with big optical lens for maximum light output and wide 54° beam angle The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance. This symbol means: indoor use only This symbol means: Read instructions This symbol means: Safety Class I appliance This symbol determines: the minimum distance from lighted objects. [. . . ] The installations should be inspected every year by a skilled person to be sure that safety is still optimal. Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. electrical installation for 1 standalone unit: Just insert the mains cable. Remark1: You can connect a CA-8 remote controller to the unit if you want to have more control. refer to "how to operate the unit" to learn how to do this. Remark2: if there's no output, please make sure to set the unit in master mode (see next chapter) Electrical installation for two or more units in master/slave: Connect 2 to maximum 16 units together using good quality balanced microphone cables. Put the first unit of the chain in master mode, the rest must be set to slave mode (SL1 or SL2). Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control over the master/slave operation Electrical installation in DMX-mode: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to "daisy chain" your DMX controller and all the connected units with a good quality balanced cable. Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these cables are compatible with balanced audio cables. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the mains input of the next MATRIX LED for easier linking. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook. Sound LED: blinks to the rhythm of the music while the unit is in audio mode 12. DOWN button: to go back in the menu and to lower the values shown on the display. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. HOW TO SET THE RIGHT STARTING ADDRESS: Refer to the next chapter (DMX-512 address setting) to learn how to set the starting address on this unit. [. . . ] Mains Input: Power consumption: Fuse: Sound Control: DMX connections: DMX channels used: Lamp: Size: Weight: AC 230V, 50Hz 29 Watt 250V 6, 3A slow blow (20mm glass) Internal microphone 3pin XLR male / female 1 or 4 or 256 channels 256 LEDs (64R + 64G + 64B + 64W) 270 x 242 x 317mm 3, 8kg Every information is subject to change without prior notice You can download the latest version of this user manual on our website: www. Ce symbole signifie: appareil construit selon les normes de sécurité classe I Ce symbole représente la distance de recul minimum à respecter, c'est-à-dire, la distance minimum entre le projecteur et la surface à éclairer. Utilisez les touches DOWN et UP pour sélectionner un des 8 shows préprogrammés : tous les shows sont présentés en mode aléatoire à 12 shows préprogrammés Une fois le show sélectionné, appuyez sur la touche ENTER pour confirmer. Mode Black out Black out mode: quand aucun signal DMX est détecté, l'appareil se met en black out. [. . . ]