User manual JBSYSTEMS LIGHT LED STRING WHITE

[. . . ] It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. In order to avoid a hazard, the unit shall only be used with the AC-adaptor delivered with it. In the event of serious operating problems, stop using the fixture and contact your dealer immediately. The housing and the lenses must be replaced if they are visibly damaged. [. . . ] Check the contents: Check that the carton contains the following items: Operating instructions 1 controller "LS-WH-CONTROL" 3 strings "LS-WH-STRING" 1 fixing eye CAUTION: To reduce the risk of electric shock, do not remove the top cover. The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. Mains connector: check if the mains voltage is not higher than 230V / 50Hz 2. Rubber seal: used to seal the program selector (5) completely from any possible moisture. Program selector: used to select one of the 16 internal programs, see chapter how to use for more information. White LED-bulbs: contains white LEDs, you can add up to 1024pcs in one line (string)!Fixing eye: can be used to clamp or stretch the string from the ceiling down etc. NEVER disconnect any parts or make any change in the setup while the installation is connected to the mains: some parts could be seriously damaged!THE SIMPLE WAY If you only want to use the standard "plug & play" starter set, things are VERY simple: just build the elements from this "LS-WH-STARTER" starter kit together and connect the complete string to the mains. THE SOPHISTICATED WAY Based on the basic "LS-WH-STARTER" set you can build a bigger system, just by adding the optionally available accessories. For each of these accessories we give a description with possible applications: LS-POWER-7A The controller of the "starter set" can control strings with up to 1024 LEDbulbs, however its internal power supply only supports up to 12 LED-bulbs. This means that you should add an extra power supply, as soon as you add extra strings. The LS-POWER-7A power supply can deliver power for up to 116 LED-bulbs. So every 116 LED-bulbs an extra LS-POWER-7A should be inserted in the line. The LS-POWER-7A contains a special POWER-T, used to "inject" the extra power into the line with strings. See the example below to learn how to insert the LS-POWER-7A: You can add one or more strings in one line until a maximum of 1024 LED-bulbs is reached. Of course you should add extra LS-POWER-7A power supplies and LS-BUFFER signal buffers where needed! LS-CURTAIN-2M An LS-CURTAIN-2M is a 2m long cable containing 8 T-connectors, used to create a nice LED-curtain. Theoretically you can connect up to 256 LS-WH-STRING cables (1024 LED-bulbs) to each of these 8 Tconnectors. Of course you should add extra LS-POWER-7A power supplies and LSBUFFER signal buffers where needed!The picture on the right gives you an idea of such a "curtain application". LS-EXTENSION-3M This 3m long cable is used for bridging the distance between two elements in a setup. [. . . ] Practically this means that when two LS-CURTAIN-2M cables are connected together in one line, a buffer should be inserted before you can connect another two LSCURTAIN-2M cables. So when 4 LS-CURTAIN-2M cables are used to make a 8M long curtain, you should add an LS-WH-STRING between the first two and the second two LS-CURTAIN-2M cables. Some general notes: Do not switch the unit on and off in short time intervals as this reduces the lamp life. Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing. [. . . ]