User manual JBSYSTEMS LIGHT LED POWER BEAM V 1.0

[. . . ] 2. 4-3--REPEAT ROW BLOCK APPLICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11. 2. 5--OPERATION WITH DMX512 Vs PiX CONTROLLER. . . . . . . . . . . . . . . . . . . . . . . 12. PART 3 DISPLAY PANEL OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. 3. 1--BASIC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. 3. 2--MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15. 3. 3--CREATING A STATIC COLOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16. 3. 4--DMX512 SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16. [. . . ] 60D iame ter( m)) GREEN 17 63 57 0 27 0 15 8 12 8 LU X 3 2 1 0 1 2 3 2(0 . 52 ) 4(1 . 05 ) 6(1 . 57 ) 8(2 . 10 ) 10 Dist ance (m) (2. 60D iame ter( m)) BLUE 30 7 98 46 27 22 LU X 3 2 1 0 1 2 3 2(0 . 52 ) 4(1 . 05 ) 6(1 . 57 ) 8(2 . 10 ) 10 Dist ance (m) (2. 60D iame ter( m)) 1 PRODUCT(GENERAL) 4 2007. 03. 10 1. 5 SAFETY WARNING IMPORTANT ALWAYS READ THE USER MANUAL BEFORE OPERATION. PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA. This product must be installed by a qualified professional. A minimum distance of 0. 5m must be maintained between the equipment and combustible surface. DO NOT stand close to the equipment and stare directly into the LED light source. Always make sure that the supporting structure is solid and can support the combined weight of the products. Do not touch the power cables if your hands are wet. ATTENTION This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual. Make sure that al parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and secure. If there is any malfunction of the equipment, contact your distributor immediately. When transferring the product, it is advisable to use the original packaging in which the product left the factory. Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired. The lamp (LED) shall be changed if it has become damaged or thermally deformed. 1 PRODUCT(GENERAL) 5 2007. 03. 10 2 INSTALLATION 2. 1 2. 2 2. 3 2. 4 MOUNTING POWER CONNECTIONS SETTING UP WITH A DMX512 CONTROLLER 2. 3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING 2. 3-2 DMX512 ADDRESSING WITH ID ADDRESS SETTING UP WITH THE PiX CONTROLLER 2. 4-1 SINGLE ROW APPLICATION 2. 4-2 STANDARD BLOCK APPLICATION 2. 4-3 REPEAT ROW BLOCK APPLICATION 2. 5 OPERATION: DMX512 Vs PiX CONTROLLER 2 INSTALLATION 6 2007. 03. 10 2. 1 MOUNTING HANGING The LED PAR can be mounted in a hanging position using the supporting bracket. The bracket should be secured to the mounting truss or structure using a standard mounting clamp. Please note that when hanging the unit a safety cable should also be used. UPRIGHT The LED PAR can be mounted in an upright or sitting position using the supporting brackets. The LED MODULE can be mounted at any angle and in any position. It is possible to further adjust the angle of the LED MODULE using the two adjustment knobs located on the side of the fixture. 2. 2 POWER CONNECTIONS @ 220V: 40 units may be connected in series @120V: 20 units may be connected in series 2 INSTALLATION 7 2007. 03. 10 2. 3 SETTING UP WITH A DMX512 CONTROLLER 2. 3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING Connect the DMX512 controller to the units in series. Each unit has 9 DMX channels so the DMX Addresses should increase by increments of 9 (e. g. 1, 10, 19, 28. . . ) The ID address has not been set so therefore when using the controller CH8 must be inactive ( CH8=0 ). Any DMX address in the range from 001 to 500 may be used. Example: DMX Addr. 1 DMX Addr. 10 DMX Addr. 19 DMX512 CONTROLLER The figure above shows a simple DMX512 layout with the starting address of the first unit set at 1, with the second set at 10 and so on. . . (Note that when used in this way, the CH8 ID function must be inactive (CH8=0)) 2. 3-2 DMX512 ADDRESSING WITH ID ADDRESS Connect the DMX512 controller to the units in series Each unit has 9 DMX channels so the DMX Addresses should increase by increments of 9 (e. g. [. . . ] The DMX address may only be selected in the range 1-250 Range Enter the number of units connected together in series. Allow edit This function allows or disables edit in Wash program , Effect program & Custom program Detect device This function enables the controller to connect to all units. When new units are attached, this function must be used to locate new units. When the controller is turned off and then on again, the controller will also detect new units. [. . . ]