User manual JBSYSTEMS LIGHT LED DJ-BAR V 1.0

[. . . ] `t Hofveld 2 ~ B1702 Groot-Bijgaarden ~ Belgium Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited. Dispose of the unit and used batteries in an environment friendly manner according to your country regulations. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit. CAUTION: To reduce the risk of electric shock, do not remove the top cover. [. . . ] Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. BUILDING TOGETHER AND INSTALLING ON A LIGHT STAND: Unpack all parts and put them on a table. Push the following parts in the correct order in the sliding section (B) located on the bottom of the 4BAR: Bolt (A) for LED panel1 Bolt (A) for LED panel2 Nut for 35mm Adapter (H) Bolt (A) for LED panel3 Bolt (A) for LED panel4 Refer to the drawing to see how the 4 panels should be fixed correctly: First add the leather washer (C) Add the metal washer (D) Add the LED PANEL (F) Important: the connector should be on the same side as the LED power signal cable (G) of the 4bar. Insert the LED power cable (G) in the back of the four corresponding panels. When the 4 panels are fixed to the 4bar, you can install the 35mm adapter (I) simply turn the thread of the adapter in the nut (H) (nut already in place) until it is well tightened. Open the knob of the adapter (J) and put the assembled LED DJ-BAR on top of a stable light stand. Tighten the knob of the adapter (J) and connect all cables (see later) You can still align the panels in different directions. DMX input DMX output ¼" Jack input for the optional CA-8 hand controller Internal microphone Slave LED: is lit when the unit is in slave mode Sound LED: blinks to the rhythm of the music while the unit is in audio mode DMX LED: is lit when the unit receives a DMX-signal Master LED: is lit when the unit is switched as master MENU button: used to select the different menu items DOWN button: to go back in the menu and to lower the values shown on the display. uP button: to go up in the menu and to increase the values shown on the display. 35mm STAND ADAPTER: used to put the LED 4Bar easily on top of a light stand Special cables with LED power signal for the passive LED panels Passive LED panels MAIN MENU: To select any of the menu options, press the MENU button up to when the required option is shown on the display. once the required menu option is selected , press the ENTER button to select. To go back to the functions without any change press the MENU button for about 2 seconds or just wait 8 seconds. Once the mode is selected, press the ENTER button to setup (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again for about 2seconds. IMPORTANT: select mode when the LED DJ-BAR is used with the LEDCON-02 controller!Show Mode Used to choose to select one of the preprogrammed shows when used in standalone or master/slave mode. Use DOWN and UP buttons to select one of the preprogrammed shows: all shows played in random mode. Except for the random show (Show 0) you will also be asked to select a running speed for the static mode. (or automatically return to the main functions without any change after 8 seconds) To go back to the functions without any change press the MENU button again for about 2seconds. Sound Mode Used to choose the desired sound mode to trigger the shows. Use DOWN and UP button to select one of the available channel modes: (sound mode ON) the shows are triggered by the internal microphone. [. . . ] BY CA-8 EASY CONTROLLER: Just connect this small controller to the 1/4" jack of the master unit, and you will be able to control the following FUNCTIONS: BUTTON ACTIONS To blackout all LED panels STANDBY Sound strobe in white 4. Sound strobe in rainbow colors PS: In this mode random show (Sh 0) is active RedOrange YellowGreen CyanBlue PurpleMagenta WhiteManual color Show1Show2 . 67 Watt T3, 15A / 250V slow blow (20mm glass) Internal microphone 3pin XLR male / female 4/13/16 channels 848 LEDs (4x 212 LEDs) see drawing 8 kg BY UNIVERSAL DMX CONTROLLER: You can use any standard DMX-controller. First choose the desired DMX-channel mode and give the unit the correct DMX start address. [. . . ]