User manual JBSYSTEMS LIGHT LED DEVIL II V 3.0

[. . . ] 0-100% dimming and ultra fast strobe function Different user modes for maximum flexibility: DMX-control: 1 channel mode or 3 channels for full control of dimmer/strobe, colors, rotation speed/direction Standalone: automatic or sound activated with internal mic Master/slave: wonderful synchronized shows Optional CA-8 remote controller available Based on a powerful 10Watt RGBW LED: Extremely brilliant beams compared to effects with halogen lamps More dynamic effects compared to effects based on halogen lamps No lamp replacements!Very low power consumption Lightweight (no lamp transformers needed) IEC power in/outlets: daisy chaining of the mains power for up to 50 units, using optional IEC-cables. This symbol means: indoor use only This symbol means: Read instructions To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. [. . . ] Should there be any, do not use the device and consult your dealer first. Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. Check the contents: Check that the carton contains the following items: Operating instructions LED DEVIL II Mains Cable Hanging bracket + 2 bolts & 2 nuts The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. Electrical installation in DMX-mode: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to "daisy chain" your DMX controller and all the connected units with a good quality balanced cable. Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these cables are compatible with balanced audio cables. pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) Pin layout XLR-5pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) ~ Pins4+5 not used. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. This input receives instructions from a DMX-controller or from another LED DEVIL II in master/slave mode. DMX output: 3pin female XLR-connector used to connect the LED DEVIL II with the next unit in the DMX chain or with another LED DEVIL II when used in master/slave mode. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the mains input of the next LED DEVIL II for easier linking. Hanging bracket with 2 knobs to fasten the unit and a mounting hole to fix a mounting hook. How to set the DIP-switches to obtain the right starting address: Each of the first 9 DIP-switches correspond to a certain DMX-value: DIP #1 #2 #3 #4 #5 #6 #7 #8 Value 1 2 4 8 16 32 64 128 Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. [. . . ] During inspection the following points should be checked: All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded. Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation. When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected. [. . . ]